4.104.115
Last change
on this file since 9647f7fe was
9647f7fe,
checked in by Thomas Doerfler <Thomas.Doerfler@…>, on 02/27/09 at 11:26:44
|
- README: Added NCS.
- Makefile.am, configure.ac, preinstall.am: Added BSP variants.
- console/console-config.c, clock/clock-config.c, ssp/ssp.c: Fixed
register settings. Cleanup.
- include/bsp.h: Added network defines and functions.
- include/lpc24xx.h: Added AHB and EMC defines. Fixed Ethernet status
sizes.
- include/system-clocks.h, misc/system-clocks.c: Added micro seconds
delay function that uses Timer 1. Changed PLL setup.
- network/network.c, startup/bspreset.c, startup/linkcmds.lpc2478,
startup/linkcmds.lpc2478_ncs, startup/linkcmds.lpc2478_ncs_ram: New
files.
- startup/bspstart.c: Added EMC initialization. Changes for ROM boot.
|
-
Property mode set to
100644
|
File size:
1.1 KB
|
Line | |
---|
1 | # |
---|
2 | # $Id$ |
---|
3 | # |
---|
4 | |
---|
5 | Development Board: QVGA Base Board from Embedded Artists |
---|
6 | |
---|
7 | http://www.embeddedartists.com/products/uclinux/oem_lpc2478.php |
---|
8 | |
---|
9 | Drivers: |
---|
10 | |
---|
11 | o Console |
---|
12 | o Clock |
---|
13 | o RTC |
---|
14 | o SSP (SPI mode): This driver is in active development. Use with care. |
---|
15 | o Network |
---|
16 | |
---|
17 | Howto setup QVGA Base Board? |
---|
18 | |
---|
19 | o Unpack board. |
---|
20 | o Connect board via USB to your PC. |
---|
21 | o Verify that demo application runs. |
---|
22 | o Disconnect board. |
---|
23 | o Change jumpers to enable ISP. |
---|
24 | o Connect board. |
---|
25 | o Load U-Boot image 'u-boot_v1.1.6_lpc2468oem_v1_8_16bit.hex' |
---|
26 | (available from the EA support page) into the flash (flash tool |
---|
27 | FlashMagic is availabe from NXP). |
---|
28 | o Change jumbers back to disable ISP. |
---|
29 | o Use a terminal program to change the U-Boot settings via the console. |
---|
30 | o U-Boot settings: |
---|
31 | set ethaddr '00:1a:f1:X:X:X' |
---|
32 | set serverip 'X.X.X.X' |
---|
33 | set ipaddr 'X.X.X.X' |
---|
34 | set rtems 'tftp a1000000 lpc2478.img;bootm' |
---|
35 | set bootcmd 'echo Booting RTEMS ...;run rtems' |
---|
36 | saveenv |
---|
37 | |
---|
38 | Application Board: NCS (Nurse Control Station) |
---|
39 | |
---|
40 | Board: NextGenNCS |
---|
41 | Processor: NXP LPC2478 |
---|
42 | SDRAM: 8MByte, 16 bit wide |
---|
43 | Ext. Flash: 1MByte, 16 bit wide |
---|
44 | Console: UART, 115200 Baud |
---|
45 | Network: 100Base-T |
---|
Note: See
TracBrowser
for help on using the repository browser.