= Mvme2307 =


{{Infobox BSP
|BSP_name     = MVME2307
|Manufacturer = Motorola
|image        = Mvme2307.jpg
|Board_URL    = http://www.mvme.com/manuals/MVME2301-to-MVME2308-spec.pdf
|Architecture = PowerPC
|CPU_model    = MPC604
|Monitor      = PPCBug
|Simulator    = Untested
|Aliases      = None known
|RAM          = 64 MB
|NVMEM        = 5 MB Flash, 8 KB NVRAM
|Serial       = 1 PC16550
|NICs         = 1 DEC 21140
|Video        = N/A
|Other        = 1 PCI Mezzanine Slot<br />PCI bus<br />VMEbus VME64
}}

The MVME2307 is a PowerPC BSP manufactured by Motorola. It includes a 32-bit MPC604 CPU, 64 MB of RAM, 5 MB of flash non-volatile memory,
and 8 KB of NVRAM non-volatile memory. Also, it has a PPCBug monitor, one PC16550 Asynchronous Serial Port, one DEC 21140 RJ-45 NIC, and
supports VMEbus VME64.
= Overview =


 *  32-bit Motorola PowerPC 604 processor
 *  PCI bus
 *  64 MB of DRAM
 *  5 MB of Flash memory
 *  1 RJ-45 DEC 21140 NIC
 *  1 PC16550 Asynchronous Serial Port
 *  1 PCI Mezzanine Slot
 *  VMEbus VME64
= Board Setup =


If there are special jumper or ROM monitor settings, describe them.
= Downloading and Executing =


This file documents the on board monitor (PPCBUG) configuration used
to be able to boot the archives located in powerpc-rtems/c/mcp750/bin.
This information was provided by Eric Valette <valette@crf.canon.fr>
= ENV command =


Use the ENV command on PPCBug to ensure that the settings are appropriate.

{{{
PPC1-Bug>env<br />
Bug or System environment [B/S] = B?<br />
Field Service Menu Enable [Y/N] = N?<br />
Probe System for Supported I/O Controllers [Y/N] = Y?<br />
Auto-Initialize of NVRAM Header Enable [Y/N] = Y?<br />
Network PReP-Boot Mode Enable [Y/N] = Y?<br />
SCSI Bus Reset on Debugger Startup [Y/N]   = N?<br />
Primary SCSI Bus Negotiations Type [A/S/N] = A?<br />
Primary SCSI Data Bus Width [W/N]          = N?<br />
Secondary SCSI Identifier                  = "07"?<br />
NVRAM Boot List (GEV.fw-boot-path) Boot Enable [Y/N]           = Y?<br />
NVRAM Boot List (GEV.fw-boot-path) Boot at power-up only [Y/N] = Y?<br />
NVRAM Boot List (GEV.fw-boot-path) Boot Abort Delay            = 5?<br />
Auto Boot Enable [Y/N]           = Y?<br />
Auto Boot at power-up only [Y/N] = Y?<br />
Auto Boot Scan Enable [Y/N]      = Y?<br />
Auto Boot Scan Device Type List  = FDISK/CDROM/TAPE/HDISK/?<br />
Auto Boot Controller LUN   = 14?<br />
Auto Boot Device LUN       = 40?<br />
Auto Boot Partition Number = 03?<br />
Auto Boot Abort Delay      = 7?<br />
Auto Boot Default String [NULL for an empty string] = ?<br />
ROM Boot Enable [Y/N]            = N?<br />
ROM Boot at power-up only [Y/N]  = Y?<br />
ROM Boot Abort Delay             = 5?<br />
ROM Boot Direct Starting Address = FFF00000?<br />
ROM Boot Direct Ending Address   = FFFFFFFC?<br />
Network Auto Boot Enable [Y/N]           = N?<br />
Network Auto Boot at power-up only [Y/N] = N?<br />
Network Auto Boot Controller LUN = 00?<br />
Network Auto Boot Device LUN     = 00?<br />
Network Auto Boot Abort Delay    = 5?<br />
Network Auto Boot Configuration Parameters Offset (NVRAM) = 00001000?<br />
Memory Size Enable [Y/N]         = Y?<br />
Memory Size Starting Address     = 00000000?<br />
Memory Size Ending Address       = 02000000?<br />
DRAM Speed in NANO Seconds       = 60?<br />
ROM First Access Length (0 - 31) = 10?<br />
ROM Next Access Length  (0 - 15) = 0?<br />
DRAM Parity Enable [On-Detection/Always/Never - O/A/N]    = O?<br />
L2Cache Parity Enable [On-Detection/Always/Never - O/A/N] = O?<br />
PCI Interrupts Route Control Registers (PIRQ0/1/2/3) = 0A050000?<br />
Serial Startup Code Master Enable [Y/N] = N?<br />
Serial Startup Code LF Enable [Y/N] =     N?<br />
}}}
= NIOT =


Use the NIOT command in PPCBug to teach the monitor about your local network and boot server.
{{{ 
PPC1-Bug>niot<br />
Controller LUN =00?<br />
Device LUN     =00?<br />
Node Control Memory Address =03F9E000?<br />
Client IP Address      =194.2.81.157?<br />
Server IP Address      =194.2.81.241?<br />
Subnet IP Address Mask =255.255.255.0?<br />
Broadcast IP Address   =255.255.255.255?<br />
Gateway IP Address     =194.2.81.254?<br />
Boot File Name ("NULL" for None)     =debug-ppc?<br />
Argument File Name ("NULL" for None) =?<br />
Boot File Load Address         =001F0000?<br />
Boot File Execution Address    =001F0000?<br />
Boot File Execution Delay      =00000000?<br />
Boot File Length               =00000000?<br />
Boot File Byte Offset          =00000000?<br />
BOOTP/RARP Request Retry       =05?<br />
TFTP/ARP Request Retry         =05?<br />
Trace Character Buffer Address =00000000?<br />
BOOTP/RARP Request Control: Always/When-Needed (A/W)=W?<br />
BOOTP/RARP Reply Update Control: Yes/No (Y/N)       =Y?<br />
}}}
= Debugging =


Unknown

=Test Reports=


Not Tested


=References=


 *  http://www.mvme.com/manuals/MVME2301-to-MVME2308-spec.pdf

{{Navbox_BSPs}}