wiki:TBR/BSP/Gen83xx

Gen83xx

Infobox BSP

BSP_name mpc8349eamds
Manufacturer Freescale
image MPC8313ERDB_PRODIMG.jpg
caption
Board_URL http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MPC8349EMDS
Architecture PowerPC
CPU_model MPC8349E processor @533MHz
Simulator No
Monitor N/A
RAM X MByte DDR-1 333MHz (supports optional ECC memory)
NVMEM 8Mbyte Flash (expandable)
Serial Dual RS232 ports
NICs Two RJ-45 G-Ethernet ports
Other optional USB and PCI Expansion module interfaces

This BSP supports boards based on the Freescale MPC834x PowerQUICC II Pro microcontrollers. The BSP supports multiple board instances through the use of BSP variants.

Overview

The MPC8313E-RDB reference platform is ideal for hardware and software development for cost-optimized networking applications. The cost-effective MPC8313E communications processor family meets the requirements of several small office/home office (SOHO), printing, IP services and industrial control applications. It leverages Freescale’s highly integrated MPC8313E processor built on Power Architecture™ technology and leading-edge external components—a 5-port Gigabit Ethernet switch, USB port, one Peripheral Component Interconnect (PCI) slot, one MiniPCI slot and one SD card memory slot. The high level of integration in the MPC8313E helps to lower overall system costs, improve performance and simplify board design.

Imported from old wiki.

  • CPU - Freescale MPC8313E running at 333/333 MHz (CPU/DDR2)
  • Memory subsystem
    • 128 MByte unbuffered DDR2 SDRAM discrete devices
    • 8 MByte Flash single-chip memory
    • 32 MByte NAND Flash memory
    • 256 KBit M24256 serial EEPROM
    • SD connector to interface with the SD memory card in SPI mode
  • Interfaces
    • 10/100/1000 BaseT Ethernet ports:
      • eTSEC1, RGMII interface: five 10/100/1000 BaseT RJ-45 interfaces using Vitesse™ VSC7385 L2 switch
      • eTSEC2, selectable RGMII or SGMII interface: one 10/100/1000 BaseT RJ-45 interface using Mavell™ 88E1111 PHY
    • USB 2.0 port:
      • High speed host/device USB interface: selectable on-chip PHY or external ULPI PHY interface by SMSC USB3300 USB PHY
    • PCI: 32-bit PCI interface running at up to 66 MHz
      • One 32-bit 3.3 V PCI slot connected to PCI bus
      • One 32-bit 3.3 V miniPCI slot connected to PCI bus
    • Dual UART ports:
      • DUART interface: supports two UART up to 115200bps for console display
  • Board connectors
    • LCD connectors by GPIO
    • ATX power supply connector
    • JTAG/COP for debugging

Board Setup

RTEMS Lab Board

Use the "printenv" command to view the firmware settings: {{{= > printenv baudrate =115200 loads_echo=1 hostname=mpc8313erdb bootfile=/tftpboot/uImage loadaddr=200000 load_uboot=tftp 100000 /tftpboot/u-boot.bin update_uboot=protect off fe000000 fe06ffff; era fe000000 fe06ffff; cp.b 100000 fe000000 $filesize burn_uboot=run load_uboot;run update_uboot netdev=eth1 nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} ramargs=setenv bootargs root=/dev/ram rw addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}:off panic=1 addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate} load_vscfw=tftp 100000 /tftpboot/vsc2bin update_vscfw=protect off fe7fe000 fe7fffff;erase fe7fe000 fe7fffff; cp.b 100000 fe7fe000 $filesize burn_vscfw=run load_vscfw; run update_vscfw run_vscld=tftp 40000 /tftpboot/vsc7385_load.bin;go 40004 run_vscld1=cp.b fe710000 40000 11000; go 40004 ethaddr=04:00:00:00:00:0A eth1addr=04:00:00:00:00:0B rootpath=/tftpboot/192.168.1.100 ethact=TSEC0 bootdelay=3 serverip=192.168.1.92 bootcmd=setenv ethact TSEC1;tftp 1000000 /mpc8313erdb.img; bootm ipaddr=192.168.1.242 stdin=serial stdout=serial stderr=serial

Environment size: 1131/8188 bytes }}}

Downloading and Executing

Use the "boot" command to download the application from the tftp server and automatically execute: {{{= > boot Speed: 100, full duplex Using TSEC1 device TFTP from server 192.168.1.92; our IP address is 192.168.1.242 Filename '/mpc8313erdb.img'. Load address: 0x1000000 Loading: ############################################ done Bytes transferred = 221368 (360b8 hex) ## Booting image at 01000000 ...

Image Name: RTEMS Created: 2011-03-24 15:56:32 UTC Image Type: PowerPC RTEMS Kernel Image (gzip compressed) Data Size: 221304 Bytes = 216.1 kB Load Address: 00000100 Entry Point: 00010000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK

## Transferring control to RTEMS (at address 00010000) ... }}}

Debugging

How do you debug code on this board? What gdb setup? BDM, stub, etc?

Test Reports

Test Report
Version CVS head
Date March 24, 2011
User User:Richard Campbell?
Report Successfully ran ticker and File I/O.

=References=

{{Navbox_BSPs}}

Last modified on 11/10/18 at 19:14:30 Last modified on 11/10/18 19:14:30

Attachments (1)

Download all attachments as: .zip