Index: networking/testing_the_driver.rst
===================================================================
--- networking/testing_the_driver.rst	(revision ca49bfd73be27cae4a7df00da22e9e7ca5bd8dfa)
+++ networking/testing_the_driver.rst	(revision d389819eea3a84e388935153e3be847342809da3)
@@ -12,5 +12,5 @@
 
 - An Ethernet network analyzer or a workstation with an
-  âEthernet snoopâ program such as ``ethersnoop`` or``tcpdump``.
+  'Ethernet snoop' program such as ``ethersnoop`` or``tcpdump``.
 
 - A workstation.
@@ -40,5 +40,5 @@
 - mbuf activity
   There are commented out calls to ``printf`` in the file``sys/mbuf.h`` in the network stack code.  Uncommenting
-  these lines results in output when mbufâs are allocated
+  these lines results in output when mbuf's are allocated
   and freed.  This is very useful for finding memory leaks.
 
@@ -92,27 +92,27 @@
   For a quick reference to the flags, see the table below:
 
-  â``U``â
+  '``U``'
       Up: The route is active.
 
-  â``H``â
+  '``H``'
       Host: The route destination is a single host.
 
-  â``G``â
+  '``G``'
       Gateway: Send anything for this destination on to this remote system, which
       will figure out from there where to send it.
 
-  â``S``â
+  '``S``'
       Static: This route was configured manually, not automatically generated by the
       system.
 
-  â``C``â
+  '``C``'
       Clone: Generates a new route based upon this route for machines we connect
       to. This type of route is normally used for local networks.
 
-  â``W``â
+  '``W``'
       WasCloned: Indicated a route that was auto-configured based upon a local area
       network (Clone) route.
 
-  â``L``â
+  '``L``'
       Link: Route involves references to Ethernet hardware.
 
@@ -183,13 +183,13 @@
   Verify that the program continues to run once the driver has been attached.
 
-- Issue a â``u``â command to send UDP
-  packets to the âdiscardâ port.
+- Issue a '``u``' command to send UDP
+  packets to the 'discard' port.
   Verify that the packets appear on the network.
 
-- Issue a â``s``â command to print the network and driver statistics.
+- Issue a '``s``' command to print the network and driver statistics.
 
 - On a workstation, add a static route to the target system.
 
-- On that same workstation try to âpingâ the target system.
+- On that same workstation try to 'ping' the target system.
   Verify that the ICMP echo request and reply packets appear on the net.
 
@@ -197,13 +197,13 @@
   Modify ``networkconfig.h`` to attach the driver
   with reception of broadcast packets enabled.
-  Try to âpingâ the target system again.
+  Try to 'ping' the target system again.
   Verify that ARP request/reply and ICMP echo request/reply packets appear
   on the net.
 
-- Issue a â``t``â command to send TCP
-  packets to the âdiscardâ port.
+- Issue a '``t``' command to send TCP
+  packets to the 'discard' port.
   Verify that the packets appear on the network.
 
-- Issue a â``s``â command to print the network and driver statistics.
+- Issue a '``s``' command to print the network and driver statistics.
 
 - Verify that you can telnet to ports 24742
@@ -233,5 +233,5 @@
   a smaller value, say 514.
 
-- âPingâ the driver from another workstation and verify
+- 'Ping' the driver from another workstation and verify
   that frames larger than 514 bytes are correctly rejected.
 
@@ -249,6 +249,6 @@
   still telnet to both the ports.
 
-- Display the driver statistics (Console â``s``â command or telnet
-  âcontrol-Gâ character) and verify that:
+- Display the driver statistics (Console '``s``' command or telnet
+  'control-G' character) and verify that:
 
   # The number of transmit interrupts is non-zero.
@@ -263,5 +263,5 @@
 - Run the ``netdemo`` program.
 
-- Issue a â``u``â console command to make the target machine transmit
+- Issue a '``u``' console command to make the target machine transmit
   a bunch of UDP packets.
 
@@ -278,5 +278,5 @@
 
 Run the ``ttcp`` network benchmark program.
-Transfer large amounts of data (100âs of megabytes) to and from the target
+Transfer large amounts of data (100's of megabytes) to and from the target
 system.
 
