Changeset 57a736ff in rtems


Ignore:
Timestamp:
Apr 11, 1998, 2:54:58 PM (22 years ago)
Author:
Joel Sherrill <joel.sherrill@…>
Branches:
4.10, 4.11, 4.8, 4.9, master
Children:
7384b1a
Parents:
6d3d425d
Message:

Mostly correcting case of section headings although a few minor things
were corrected as the Getting Started with GNAT/RTEMS manual was
created.

Location:
doc/started
Files:
5 edited

Legend:

Unmodified
Added
Removed
  • doc/started/Makefile

    r6d3d425d r57a736ff  
    5151
    5252require.texi: require.t versions.texi
    53         $(BMENU) -c -p "Introduction" \
     53        $(BMENU) -c -p "Cross Development" \
    5454            -u "Top" \
    5555            -n "Building the GNU C/C++ Cross Compiler Toolset" ${*}.t
     
    6666
    6767sample.texi: sample.t versions.texi
    68         $(BMENU) -c -p "Generate RTEMS for a specific target and board support package" \
     68        $(BMENU) -c -p "Generate RTEMS for a Specific Target and Board Support Package" \
    6969            -u "Top" \
    7070            -n "Building the GNU Debugger" ${*}.t
    7171
    7272gdb.texi: gdb.t versions.texi
    73         $(BMENU) -c -p "Application executable" \
     73        $(BMENU) -c -p "Application Executable" \
    7474            -u "Top" \
    7575            -n "" ${*}.t
  • doc/started/buildc.t

    r6d3d425d r57a736ff  
    1414toolset and install it.
    1515
    16 @section Get all the pieces
     16@section Directory Organization
    1717
    1818The tree structure in the figure below is assumed to be present in the
     
    2020
    2121@center @b{XXX directory tree figure goes here}
     22
     23@section Get All the Pieces
    2224
    2325Gather the components that will be required for the installation and place
     
    5355    File:        @value{RTEMS-TAR}
    5456    File:        bit
     57@ifset BINUTILS-RTEMSPATCH
    5558    File:        @value{BINUTILS-RTEMSPATCH}
     59@end ifset
     60@ifset NEWLIB-RTEMSPATCH
    5661    File:        @value{NEWLIB-RTEMSPATCH}
     62@end ifset
     63@ifset GCC-RTEMSPATCH
    5764    File:        @value{GCC-RTEMSPATCH}
     65@end ifset
    5866    File:        hello_world_c.tgz
    5967@end example
    6068
    6169
    62 @section Create the tools directory
     70@section Create the tools Directory
    6371
    6472Create a directory called tools that will serve as a working directory to
  • doc/started/buildrt.t

    r6d3d425d r57a736ff  
    1010@chapter Building RTEMS
    1111
    12 @section Unpack the RTEMS source
     12@section Unpack the RTEMS Source
    1313
    1414Use the following command sequence to unpack the RTEMS source into the
     
    2020@end example
    2121
    22 @section Add the bin directory under the install point to the default PATH
     22@section Add <INSTALL_POINT>/bin to Executable PATH
    2323
    2424In order to compile RTEMS, you must have the cross compilation toolset
     
    3434work with the C Shell (@code{csh})or derivatives of the C Shell.
    3535
    36 @section Generate RTEMS for a specific target and board support package
     36@section Generate RTEMS for a Specific Target and BSP
    3737
    3838Make a build directory under tools and build the RTEMS product in this
     
    5959@end example
    6060
    61 Where:
    62 
    63 The list of currently supported of <TARGET_CONFIGURATION>'s and
     61Where the list of currently supported of <TARGET_CONFIGURATION>'s and
    6462<BOARD_SUPPORT_PACKAGE>'s can be found in
    6563tools/@value{RTEMS-UNTAR}/README.configure.
  • doc/started/gdb.t

    r6d3d425d r57a736ff  
    2121but are not documented here.
    2222
    23 @section Unarchive the gdb distribution
     23@section Unarchive the gdb Distribution
    2424
    2525Use the following commands to unarchive the gdb distribution:
     
    7777@section GDB with Sparc Instruction Simulation (SIS)
    7878
    79 @subheading Make the build directory
     79@subheading Make the Build Directory
    8080
    8181Create a build directory for the SIS Debugger
     
    8686@end example
    8787
    88 @subheading Configure for the build
     88@subheading Configure for the Build
    8989
    9090Configure the GNU Debugger for the
     
    103103with SIS will be created.
    104104
    105 @subheading Make the debugger
     105@subheading Make the Debugger
    106106
    107107From tools/build-sis execute the following command sequence:
     
    114114@section GDB with PowerPC Instruction Simulator
    115115
    116 @subheading Make the build directory
     116@subheading Make the Build Directory
    117117
    118118Create a build directory for the SIS Debugger
     
    123123@end example
    124124
    125 @subheading Configure for the build
     125@subheading Configure for the Build
    126126
    127127Configure the GNU Debugger for the PowerPC
     
    145145
    146146
    147 @subheading Make the debugger
     147@subheading Make the Debugger
    148148
    149149From tools/build-ppc execute the following command sequence:
     
    156156@section GDB for DINK32
    157157
    158 @subheading Unarchive the gdb distribution
    159 
    160 Use the following commands to unarchive the gdb distribution:
    161 
    162 @subheading Make the build directory
     158@subheading Make the Build Directory
    163159
    164160Create a build directory for the DINK32 Debugger
     
    169165@end example
    170166
    171 @subheading Configure for the build
     167@subheading Configure for the Build
    172168
    173169Configure the GNU Debugger to communicate with
     
    185181gdb Dink32 will be created.
    186182
    187 @subheading Make the debugger
     183@subheading Make the Debugger
    188184
    189185From tools/build-dink32 execute the following command sequence:
  • doc/started/sample.t

    r6d3d425d r57a736ff  
    99@chapter Building the Sample Application
    1010
    11 @section Unpack the sample application
     11@section Unpack the Sample Application
    1212
    1313Use the following command to unarchive the sample application:
     
    1818@end example
    1919
    20 @section Set the environment variable RTEMS_MAKEFILE_PATH
     20@section Set the Environment Variable RTEMS_MAKEFILE_PATH
    2121
    2222It must point to the appropriate directory containing RTEMS build for our
     
    2828@end example
    2929
    30 Where:
    31 
    32 <INSTALLATION_POINT> and <BOARD_SUPPORT_PACKAGE> are those used when
     30Where <INSTALLATION_POINT> and <BOARD_SUPPORT_PACKAGE> are those used when
    3331configuring and installing RTEMS.
    3432
     
    4745combination was done properly.
    4846
    49 @section Application executable
     47@section Application Executable
    5048
    5149If the sample application has successfully been build, then the application
     
    5351
    5452@example
    55 tools/simple_app/o-<BOARD_SUPPORT_PACKAGE>/<filename>.exe
     53tools/hello_world_c/o-<BOARD_SUPPORT_PACKAGE>/<filename>.exe
    5654@end example
    5755
Note: See TracChangeset for help on using the changeset viewer.