source: rtems/cpukit/score/cpu/sparc/include/rtems/score/cpu.h @ c8df844

/**
 * @file
 *
 * @brief SPARC CPU Department Source
 *
 * This include file contains information pertaining to the port of
 * the executive to the SPARC processor.
 */

/*
 *  COPYRIGHT (c) 1989-2011.
 *  On-Line Applications Research Corporation (OAR).
 *
 *  The license and distribution terms for this file may be
 *  found in the file LICENSE in this distribution or at
 *  http://www.rtems.org/license/LICENSE.
 */

#ifndef _RTEMS_SCORE_CPU_H
#define _RTEMS_SCORE_CPU_H

#ifdef __cplusplus
extern "C" {
#endif

#include <rtems/score/basedefs.h>
#include <rtems/score/sparc.h>

/* conditional compilation parameters */

/*
 * The SPARC ABI is a bit special with respect to the floating point context.
 * The complete floating point context is volatile.  Thus, from an ABI point
 * of view nothing needs to be saved and restored during a context switch.
 * Instead the floating point context must be saved and restored during
 * interrupt processing.  Historically, the deferred floating point switch was
 * used for SPARC and the complete floating point context is saved and
 * restored during a context switch to the new floating point unit owner.
 * This is a bit dangerous since post-switch actions (e.g. signal handlers)
 * and context switch extensions may silently corrupt the floating point
 * context.
 *
 * The floating point unit is disabled for interrupt handlers.  Thus, in case
 * an interrupt handler uses the floating point unit then this will result in a
 * trap (INTERNAL_ERROR_ILLEGAL_USE_OF_FLOATING_POINT_UNIT).
 *
 * In uniprocessor configurations, a lazy floating point context switch is
 * used.  In case an active floating point thread is interrupted (PSR[EF] == 1)
 * and a thread dispatch is carried out, then this thread is registered as the
 * floating point owner.  When a floating point owner is present during a
 * context switch, the floating point unit is disabled for the heir thread
 * (PSR[EF] == 0).  The floating point disabled trap checks that the use of the
 * floating point unit is allowed and saves/restores the floating point context
 * on demand.
 *
 * In SMP configurations, the deferred floating point switch is not supported
 * in principle.  So, use here a synchronous floating point switching.
 * Synchronous means that the volatile floating point context is saved and
 * restored around a thread dispatch issued during interrupt processing.  Thus
 * post-switch actions and context switch extensions may safely use the
 * floating point unit.
 */
#if SPARC_HAS_FPU == 1
  #if defined(RTEMS_SMP)
    #define SPARC_USE_SYNCHRONOUS_FP_SWITCH
  #else
    #define SPARC_USE_LAZY_FP_SWITCH
  #endif
#endif

/**
 * Does the executive manage a dedicated interrupt stack in software?
 *
 * If TRUE, then a stack is allocated in _ISR_Handler_initialization.
 * If FALSE, nothing is done.
 *
 * The SPARC does not have a dedicated HW interrupt stack and one has
 * been implemented in SW.
 */
#define CPU_HAS_SOFTWARE_INTERRUPT_STACK   TRUE

/**
 * Does the CPU follow the simple vectored interrupt model?
 *
 * - If TRUE, then RTEMS allocates the vector table it internally manages.
 * - If FALSE, then the BSP is assumed to allocate and manage the vector
 *   table
 *
 * THe SPARC is a simple vectored architecture.  Usually there is no
 * PIC and the CPU directly vectors the interrupts.
 */
#define CPU_SIMPLE_VECTORED_INTERRUPTS TRUE

/**
 * Does this CPU have hardware support for a dedicated interrupt stack?
 *
 * - If TRUE, then it must be installed during initialization.
 * - If FALSE, then no installation is performed.
 *
 * The SPARC does not have a dedicated HW interrupt stack.
 */
#define CPU_HAS_HARDWARE_INTERRUPT_STACK  FALSE

/**
 * Do we allocate a dedicated interrupt stack in the Interrupt Manager?
 *
 * - If TRUE, then the memory is allocated during initialization.
 * - If FALSE, then the memory is allocated during initialization.
 *
 * The SPARC does not have hardware support for switching to a
 * dedicated interrupt stack.  The port includes support for doing this
 * in software.
 *
 */
#define CPU_ALLOCATE_INTERRUPT_STACK      TRUE

/**
 * Does the RTEMS invoke the user's ISR with the vector number and
 * a pointer to the saved interrupt frame (1) or just the vector
 * number (0)?
 *
 * The SPARC port does not pass an Interrupt Stack Frame pointer to
 * interrupt handlers.
 */
#define CPU_ISR_PASSES_FRAME_POINTER FALSE

/**
 * Does the CPU have hardware floating point?
 *
 * - If TRUE, then the FLOATING_POINT task attribute is supported.
 * - If FALSE, then the FLOATING_POINT task attribute is ignored.
 *
 * This is set based upon the multilib settings.
 */
#if ( SPARC_HAS_FPU == 1 ) && !defined(SPARC_USE_SYNCHRONOUS_FP_SWITCH)
  #define CPU_HARDWARE_FP     TRUE
#else
  #define CPU_HARDWARE_FP     FALSE
#endif

/**
 * The SPARC GCC port does not have a software floating point library
 * that requires RTEMS assistance.
 */
#define CPU_SOFTWARE_FP     FALSE

/**
 * Are all tasks FLOATING_POINT tasks implicitly?
 *
 * - If TRUE, then the FLOATING_POINT task attribute is assumed.
 * - If FALSE, then the FLOATING_POINT task attribute is followed.
 *
 * The SPARC GCC port does not implicitly use floating point registers.
 */
#define CPU_ALL_TASKS_ARE_FP     FALSE

/**
 * Should the IDLE task have a floating point context?
 *
 * - If TRUE, then the IDLE task is created as a FLOATING_POINT task
 *   and it has a floating point context which is switched in and out.
 * - If FALSE, then the IDLE task does not have a floating point context.
 *
 * The IDLE task does not have to be floating point on the SPARC.
 */
#define CPU_IDLE_TASK_IS_FP      FALSE

#define CPU_USE_DEFERRED_FP_SWITCH FALSE

#define CPU_ENABLE_ROBUST_THREAD_DISPATCH FALSE

/**
 * Does this port provide a CPU dependent IDLE task implementation?
 *
 * - If TRUE, then the routine _CPU_Thread_Idle_body
 * must be provided and is the default IDLE thread body instead of
 * _CPU_Thread_Idle_body.
 *
 * - If FALSE, then use the generic IDLE thread body if the BSP does
 * not provide one.
 *
 * The SPARC architecture does not have a low power or halt instruction.
 * It is left to the BSP and/or CPU specific code to provide an IDLE
 * thread body which is aware of low power modes.
 */
#define CPU_PROVIDES_IDLE_THREAD_BODY    FALSE

/**
 * Does the stack grow up (toward higher addresses) or down
 * (toward lower addresses)?
 *
 * - If TRUE, then the grows upward.
 * - If FALSE, then the grows toward smaller addresses.
 *
 * The stack grows to lower addresses on the SPARC.
 */
#define CPU_STACK_GROWS_UP               FALSE

/* LEON3 systems may use a cache line size of 64 */
#define CPU_CACHE_LINE_BYTES 64

#define CPU_STRUCTURE_ALIGNMENT RTEMS_ALIGNED( CPU_CACHE_LINE_BYTES )

/**
 * The following defines the number of bits actually used in the
 * interrupt field of the task mode.  How those bits map to the
 * CPU interrupt levels is defined by the routine _CPU_ISR_Set_level().
 *
 * The SPARC has 16 interrupt levels in the PIL field of the PSR.
 */
#define CPU_MODES_INTERRUPT_MASK   0x0000000F

#ifndef ASM
/**
 * This structure represents the organization of the minimum stack frame
 * for the SPARC.  More framing information is required in certain situaions
 * such as when there are a large number of out parameters or when the callee
 * must save floating point registers.
 */
typedef struct {
  /** This is the offset of the l0 register. */
  uint32_t    l0;
  /** This is the offset of the l1 register. */
  uint32_t    l1;
  /** This is the offset of the l2 register. */
  uint32_t    l2;
  /** This is the offset of the l3 register. */
  uint32_t    l3;
  /** This is the offset of the l4 register. */
  uint32_t    l4;
  /** This is the offset of the l5 register. */
  uint32_t    l5;
  /** This is the offset of the l6 register. */
  uint32_t    l6;
  /** This is the offset of the l7 register. */
  uint32_t    l7;
  /** This is the offset of the l0 register. */
  uint32_t    i0;
  /** This is the offset of the i1 register. */
  uint32_t    i1;
  /** This is the offset of the i2 register. */
  uint32_t    i2;
  /** This is the offset of the i3 register. */
  uint32_t    i3;
  /** This is the offset of the i4 register. */
  uint32_t    i4;
  /** This is the offset of the i5 register. */
  uint32_t    i5;
  /** This is the offset of the i6 register. */
  uint32_t    i6_fp;
  /** This is the offset of the i7 register. */
  uint32_t    i7;
  /** This is the offset of the register used to return structures. */
  void       *structure_return_address;

  /*
   * The following are for the callee to save the register arguments in
   * should this be necessary.
   */
  /** This is the offset of the register for saved argument 0. */
  uint32_t    saved_arg0;
  /** This is the offset of the register for saved argument 1. */
  uint32_t    saved_arg1;
  /** This is the offset of the register for saved argument 2. */
  uint32_t    saved_arg2;
  /** This is the offset of the register for saved argument 3. */
  uint32_t    saved_arg3;
  /** This is the offset of the register for saved argument 4. */
  uint32_t    saved_arg4;
  /** This is the offset of the register for saved argument 5. */
  uint32_t    saved_arg5;
  /** This field pads the structure so ldd and std instructions can be used. */
  uint32_t    pad0;
} SPARC_Minimum_stack_frame;

#endif /* ASM */

/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_L0_OFFSET             0x00
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_L1_OFFSET             0x04
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_L2_OFFSET             0x08
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_L3_OFFSET             0x0c
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_L4_OFFSET             0x10
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_L5_OFFSET             0x14
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_L6_OFFSET             0x18
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_L7_OFFSET             0x1c
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_I0_OFFSET             0x20
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_I1_OFFSET             0x24
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_I2_OFFSET             0x28
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_I3_OFFSET             0x2c
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_I4_OFFSET             0x30
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_I5_OFFSET             0x34
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_I6_FP_OFFSET          0x38
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_I7_OFFSET             0x3c
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STRUCTURE_RETURN_ADDRESS_OFFSET   0x40
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_SAVED_ARG0_OFFSET     0x44
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_SAVED_ARG1_OFFSET     0x48
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_SAVED_ARG2_OFFSET     0x4c
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_SAVED_ARG3_OFFSET     0x50
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_SAVED_ARG4_OFFSET     0x54
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_SAVED_ARG5_OFFSET     0x58
/** This macro defines an offset into the stack frame for use in assembly. */
#define CPU_STACK_FRAME_PAD0_OFFSET           0x5c

#define CPU_MAXIMUM_PROCESSORS 32

/**
 * @defgroup Contexts SPARC Context Structures
 *
 * @ingroup Score
 *
 * Generally there are 2 types of context to save.
 *    + Interrupt registers to save
 *    + Task level registers to save
 *
 * This means we have the following 3 context items:
 *    + task level context stuff::  Context_Control
 *    + floating point task stuff:: Context_Control_fp
 *    + special interrupt level context :: Context_Control_interrupt
 *
 * On the SPARC, we are relatively conservative in that we save most
 * of the CPU state in the context area.  The ET (enable trap) bit and
 * the CWP (current window pointer) fields of the PSR are considered
 * system wide resources and are not maintained on a per-thread basis.
 */
/**@{**/

#ifndef ASM
typedef struct Context_Control_fp Context_Control_fp;

/**
 * @brief SPARC basic context.
 *
 * This structure defines the non-volatile integer and processor state context
 * for the SPARC architecture according to "SYSTEM V APPLICATION BINARY
 * INTERFACE - SPARC Processor Supplement", Third Edition.
 *
 * The registers g2 through g4 are reserved for applications.  GCC uses them as
 * volatile registers by default.  So they are treated like volatile registers
 * in RTEMS as well.
 *
 * The register g6 contains the per-CPU control of the current processor.  It
 * is an invariant of the processor context.  This register must not be saved
 * and restored during context switches or interrupt services.
 */
typedef struct {
  /** This will contain the contents of the g5 register. */
  uint32_t   g5;
  /** This will contain the contents of the g7 register. */
  uint32_t   g7;

  /**
   * This will contain the contents of the l0 and l1 registers.
   *
   * Using a double l0_and_l1 will put everything in this structure on a double
   * word boundary which allows us to use double word loads and stores safely
   * in the context switch.
   */
  double     l0_and_l1;
  /** This will contain the contents of the l2 register. */
  uint32_t   l2;
  /** This will contain the contents of the l3 register. */
  uint32_t   l3;
  /** This will contain the contents of the l4 register. */
  uint32_t   l4;
  /** This will contain the contents of the l5 registeer.*/
  uint32_t   l5;
  /** This will contain the contents of the l6 register. */
  uint32_t   l6;
  /** This will contain the contents of the l7 register. */
  uint32_t   l7;

  /** This will contain the contents of the i0 register. */
  uint32_t   i0;
  /** This will contain the contents of the i1 register. */
  uint32_t   i1;
  /** This will contain the contents of the i2 register. */
  uint32_t   i2;
  /** This will contain the contents of the i3 register. */
  uint32_t   i3;
  /** This will contain the contents of the i4 register. */
  uint32_t   i4;
  /** This will contain the contents of the i5 register. */
  uint32_t   i5;
  /** This will contain the contents of the i6 (e.g. frame pointer) register. */
  uint32_t   i6_fp;
  /** This will contain the contents of the i7 register. */
  uint32_t   i7;

  /** This will contain the contents of the o6 (e.g. frame pointer) register. */
  uint32_t   o6_sp;
  /**
   * This will contain the contents of the o7 (e.g. address of CALL
   * instruction) register.
   */
  uint32_t   o7;

  /** This will contain the contents of the processor status register. */
  uint32_t   psr;
  /**
   * This field is used to prevent heavy nesting of calls to _Thread_Dispatch
   * on an interrupted  task's stack.  This is problematic on the slower
   * SPARC CPU models at high interrupt rates.
   */
  uint32_t   isr_dispatch_disable;

#if defined(SPARC_USE_LAZY_FP_SWITCH)
  Context_Control_fp *fp_context;
#endif

#if defined(RTEMS_SMP)
  volatile uint32_t is_executing;
#endif
} Context_Control;

/**
 * This macro provides a CPU independent way for RTEMS to access the
 * stack pointer in a context structure. The actual name and offset is
 * CPU architecture dependent.
 */
#define _CPU_Context_Get_SP( _context ) \
  (_context)->o6_sp

#ifdef RTEMS_SMP
  static inline bool _CPU_Context_Get_is_executing(
    const Context_Control *context
  )
  {
    return context->is_executing;
  }

  static inline void _CPU_Context_Set_is_executing(
    Context_Control *context,
    bool is_executing
  )
  {
    context->is_executing = is_executing;
  }
#endif

#endif /* ASM */

/*
 *  Offsets of fields with Context_Control for assembly routines.
 */

/** This macro defines an offset into the context for use in assembly. */
#define G5_OFFSET    0x00
/** This macro defines an offset into the context for use in assembly. */
#define G7_OFFSET    0x04

/** This macro defines an offset into the context for use in assembly. */
#define L0_OFFSET    0x08
/** This macro defines an offset into the context for use in assembly. */
#define L1_OFFSET    0x0C
/** This macro defines an offset into the context for use in assembly. */
#define L2_OFFSET    0x10
/** This macro defines an offset into the context for use in assembly. */
#define L3_OFFSET    0x14
/** This macro defines an offset into the context for use in assembly. */
#define L4_OFFSET    0x18
/** This macro defines an offset into the context for use in assembly. */
#define L5_OFFSET    0x1C
/** This macro defines an offset into the context for use in assembly. */
#define L6_OFFSET    0x20
/** This macro defines an offset into the context for use in assembly. */
#define L7_OFFSET    0x24

/** This macro defines an offset into the context for use in assembly. */
#define I0_OFFSET    0x28
/** This macro defines an offset into the context for use in assembly. */
#define I1_OFFSET    0x2C
/** This macro defines an offset into the context for use in assembly. */
#define I2_OFFSET    0x30
/** This macro defines an offset into the context for use in assembly. */
#define I3_OFFSET    0x34
/** This macro defines an offset into the context for use in assembly. */
#define I4_OFFSET    0x38
/** This macro defines an offset into the context for use in assembly. */
#define I5_OFFSET    0x3C
/** This macro defines an offset into the context for use in assembly. */
#define I6_FP_OFFSET 0x40
/** This macro defines an offset into the context for use in assembly. */
#define I7_OFFSET    0x44

/** This macro defines an offset into the context for use in assembly. */
#define O6_SP_OFFSET 0x48
/** This macro defines an offset into the context for use in assembly. */
#define O7_OFFSET    0x4C

/** This macro defines an offset into the context for use in assembly. */
#define PSR_OFFSET   0x50
/** This macro defines an offset into the context for use in assembly. */
#define ISR_DISPATCH_DISABLE_STACK_OFFSET 0x54

#if defined(RTEMS_SMP)
  #define SPARC_CONTEXT_CONTROL_IS_EXECUTING_OFFSET 0x58
#endif

#ifndef ASM
/**
 * @brief SPARC basic context.
 *
 * This structure defines floating point context area.
 */
struct Context_Control_fp {
  /** This will contain the contents of the f0 and f1 register. */
  double      f0_f1;
  /** This will contain the contents of the f2 and f3 register. */
  double      f2_f3;
  /** This will contain the contents of the f4 and f5 register. */
  double      f4_f5;
  /** This will contain the contents of the f6 and f7 register. */
  double      f6_f7;
  /** This will contain the contents of the f8 and f9 register. */
  double      f8_f9;
  /** This will contain the contents of the f10 and f11 register. */
  double      f10_f11;
  /** This will contain the contents of the f12 and f13 register. */
  double      f12_f13;
  /** This will contain the contents of the f14 and f15 register. */
  double      f14_f15;
  /** This will contain the contents of the f16 and f17 register. */
  double      f16_f17;
  /** This will contain the contents of the f18 and f19 register. */
  double      f18_f19;
  /** This will contain the contents of the f20 and f21 register. */
  double      f20_f21;
  /** This will contain the contents of the f22 and f23 register. */
  double      f22_f23;
  /** This will contain the contents of the f24 and f25 register. */
  double      f24_f25;
  /** This will contain the contents of the f26 and f27 register. */
  double      f26_f27;
  /** This will contain the contents of the f28 and f29 register. */
  double      f28_f29;
  /** This will contain the contents of the f30 and f31 register. */
  double      f30_f31;
  /** This will contain the contents of the floating point status register. */
  uint32_t    fsr;
};

#endif /* ASM */

/*
 *  Offsets of fields with Context_Control_fp for assembly routines.
 */

/** This macro defines an offset into the FPU context for use in assembly. */
#define FO_F1_OFFSET     0x00
/** This macro defines an offset into the FPU context for use in assembly. */
#define F2_F3_OFFSET     0x08
/** This macro defines an offset into the FPU context for use in assembly. */
#define F4_F5_OFFSET     0x10
/** This macro defines an offset into the FPU context for use in assembly. */
#define F6_F7_OFFSET     0x18
/** This macro defines an offset into the FPU context for use in assembly. */
#define F8_F9_OFFSET     0x20
/** This macro defines an offset into the FPU context for use in assembly. */
#define F1O_F11_OFFSET   0x28
/** This macro defines an offset into the FPU context for use in assembly. */
#define F12_F13_OFFSET   0x30
/** This macro defines an offset into the FPU context for use in assembly. */
#define F14_F15_OFFSET   0x38
/** This macro defines an offset into the FPU context for use in assembly. */
#define F16_F17_OFFSET   0x40
/** This macro defines an offset into the FPU context for use in assembly. */
#define F18_F19_OFFSET   0x48
/** This macro defines an offset into the FPU context for use in assembly. */
#define F2O_F21_OFFSET   0x50
/** This macro defines an offset into the FPU context for use in assembly. */
#define F22_F23_OFFSET   0x58
/** This macro defines an offset into the FPU context for use in assembly. */
#define F24_F25_OFFSET   0x60
/** This macro defines an offset into the FPU context for use in assembly. */
#define F26_F27_OFFSET   0x68
/** This macro defines an offset into the FPU context for use in assembly. */
#define F28_F29_OFFSET   0x70
/** This macro defines an offset into the FPU context for use in assembly. */
#define F3O_F31_OFFSET   0x78
/** This macro defines an offset into the FPU context for use in assembly. */
#define FSR_OFFSET       0x80

/** This defines the size of the FPU context area for use in assembly. */
#define CONTEXT_CONTROL_FP_SIZE 0x84

#ifndef ASM

/** @} */

/**
 * @brief Interrupt stack frame (ISF).
 *
 * Context saved on stack for an interrupt.
 *
 * NOTE: The PSR, PC, and NPC are only saved in this structure for the
 *       benefit of the user's handler.
 */
typedef struct {
  /** On an interrupt, we must save the minimum stack frame. */
  SPARC_Minimum_stack_frame Stack_frame;
  /** This is the offset of the PSR on an ISF. */
  uint32_t                 psr;
  /** This is the offset of the XXX on an ISF. */
  uint32_t                 pc;
  /** This is the offset of the XXX on an ISF. */
  uint32_t                 npc;
  /** This is the offset of the g1 register on an ISF. */
  uint32_t                 g1;
  /** This is the offset of the g2 register on an ISF. */
  uint32_t                 g2;
  /** This is the offset of the g3 register on an ISF. */
  uint32_t                 g3;
  /** This is the offset of the g4 register on an ISF. */
  uint32_t                 g4;
  /** This is the offset of the g5 register on an ISF. */
  uint32_t                 g5;
  /** This is the offset is reserved for alignment on an ISF. */
  uint32_t                 reserved_for_alignment;
  /** This is the offset of the g7 register on an ISF. */
  uint32_t                 g7;
  /** This is the offset of the i0 register on an ISF. */
  uint32_t                 i0;
  /** This is the offset of the i1 register on an ISF. */
  uint32_t                 i1;
  /** This is the offset of the i2 register on an ISF. */
  uint32_t                 i2;
  /** This is the offset of the i3 register on an ISF. */
  uint32_t                 i3;
  /** This is the offset of the i4 register on an ISF. */
  uint32_t                 i4;
  /** This is the offset of the i5 register on an ISF. */
  uint32_t                 i5;
  /** This is the offset of the i6 register on an ISF. */
  uint32_t                 i6_fp;
  /** This is the offset of the i7 register on an ISF. */
  uint32_t                 i7;
  /** This is the offset of the y register on an ISF. */
  uint32_t                 y;
  /** This is the offset of the tpc register on an ISF. */
  uint32_t                 tpc;
} CPU_Interrupt_frame;

#endif /* ASM */

#ifndef ASM
/**
 * The following type defines an entry in the SPARC's trap table.
 *
 * NOTE: The instructions chosen are RTEMS dependent although one is
 *       obligated to use two of the four instructions to perform a
 *       long jump.  The other instructions load one register with the
 *       trap type (a.k.a. vector) and another with the psr.
 */
typedef struct {
  /** This will contain a "mov %psr, %l0" instruction. */
  uint32_t     mov_psr_l0;
  /** This will contain a "sethi %hi(_handler), %l4" instruction. */
  uint32_t     sethi_of_handler_to_l4;
  /** This will contain a "jmp %l4 + %lo(_handler)" instruction. */
  uint32_t     jmp_to_low_of_handler_plus_l4;
  /** This will contain a " mov _vector, %l3" instruction. */
  uint32_t     mov_vector_l3;
} CPU_Trap_table_entry;

/**
 * This is the set of opcodes for the instructions loaded into a trap
 * table entry.  The routine which installs a handler is responsible
 * for filling in the fields for the _handler address and the _vector
 * trap type.
 *
 * The constants following this structure are masks for the fields which
 * must be filled in when the handler is installed.
 */
extern const CPU_Trap_table_entry _CPU_Trap_slot_template;

/**
 * The size of the floating point context area.
 */
#define CPU_CONTEXT_FP_SIZE sizeof( Context_Control_fp )

#endif

/**
 * Amount of extra stack (above minimum stack size) required by
 * MPCI receive server thread.  Remember that in a multiprocessor
 * system this thread must exist and be able to process all directives.
 */
#define CPU_MPCI_RECEIVE_SERVER_EXTRA_STACK 1024

/**
 * This defines the number of entries in the ISR_Vector_table managed
 * by the executive.
 *
 * On the SPARC, there are really only 256 vectors.  However, the executive
 * has no easy, fast, reliable way to determine which traps are synchronous
 * and which are asynchronous.  By default, synchronous traps return to the
 * instruction which caused the interrupt.  So if you install a software
 * trap handler as an executive interrupt handler (which is desirable since
 * RTEMS takes care of window and register issues), then the executive needs
 * to know that the return address is to the trap rather than the instruction
 * following the trap.
 *
 * So vectors 0 through 255 are treated as regular asynchronous traps which
 * provide the "correct" return address.  Vectors 256 through 512 are assumed
 * by the executive to be synchronous and to require that the return address
 * be fudged.
 *
 * If you use this mechanism to install a trap handler which must reexecute
 * the instruction which caused the trap, then it should be installed as
 * an asynchronous trap.  This will avoid the executive changing the return
 * address.
 */
#define CPU_INTERRUPT_NUMBER_OF_VECTORS     256

/**
 * The SPARC has 256 vectors but the port treats 256-512 as synchronous
 * traps.
 */
#define CPU_INTERRUPT_MAXIMUM_VECTOR_NUMBER 511

/**
 * This is the bit step in a vector number to indicate it is being installed
 * as a synchronous trap.
 */
#define SPARC_SYNCHRONOUS_TRAP_BIT_MASK     0x100

/**
 * This macro indicates that @a _trap as an asynchronous trap.
 */
#define SPARC_ASYNCHRONOUS_TRAP( _trap )    (_trap)

/**
 * This macro indicates that @a _trap as a synchronous trap.
 */
#define SPARC_SYNCHRONOUS_TRAP( _trap )     ((_trap) + 256 )

/**
 * This macro returns the real hardware vector number associated with @a _trap.
 */
#define SPARC_REAL_TRAP_NUMBER( _trap )     ((_trap) % 256)

/**
 * This is defined if the port has a special way to report the ISR nesting
 * level.  Most ports maintain the variable _ISR_Nest_level.
 */
#define CPU_PROVIDES_ISR_IS_IN_PROGRESS FALSE

/**
 * Should be large enough to run all tests.  This ensures
 * that a "reasonable" small application should not have any problems.
 *
 * This appears to be a fairly generous number for the SPARC since
 * represents a call depth of about 20 routines based on the minimum
 * stack frame.
 */
#define CPU_STACK_MINIMUM_SIZE  (1024*4)

/**
 * What is the size of a pointer on this architecture?
 */
#define CPU_SIZEOF_POINTER 4

/**
 * CPU's worst alignment requirement for data types on a byte boundary.  This
 * alignment does not take into account the requirements for the stack.
 *
 * On the SPARC, this is required for double word loads and stores.
 */
#define CPU_ALIGNMENT      8

/**
 * This number corresponds to the byte alignment requirement for the
 * heap handler.  This alignment requirement may be stricter than that
 * for the data types alignment specified by CPU_ALIGNMENT.  It is
 * common for the heap to follow the same alignment requirement as
 * CPU_ALIGNMENT.  If the CPU_ALIGNMENT is strict enough for the heap,
 * then this should be set to CPU_ALIGNMENT.
 *
 * NOTE:  This does not have to be a power of 2.  It does have to
 *        be greater or equal to than CPU_ALIGNMENT.
 */
#define CPU_HEAP_ALIGNMENT         CPU_ALIGNMENT

/**
 * This number corresponds to the byte alignment requirement for memory
 * buffers allocated by the partition manager.  This alignment requirement
 * may be stricter than that for the data types alignment specified by
 * CPU_ALIGNMENT.  It is common for the partition to follow the same
 * alignment requirement as CPU_ALIGNMENT.  If the CPU_ALIGNMENT is strict
 * enough for the partition, then this should be set to CPU_ALIGNMENT.
 *
 * NOTE:  This does not have to be a power of 2.  It does have to
 *        be greater or equal to than CPU_ALIGNMENT.
 */
#define CPU_PARTITION_ALIGNMENT    CPU_ALIGNMENT

/**
 * Stack frames must be doubleword aligned according to the System V ABI for
 * SPARC.
 */
#define CPU_STACK_ALIGNMENT CPU_ALIGNMENT

#define CPU_INTERRUPT_STACK_ALIGNMENT CPU_CACHE_LINE_BYTES

#ifndef ASM

/*
 *  ISR handler macros
 */

/**
 * Support routine to initialize the RTEMS vector table after it is allocated.
 */
#define _CPU_Initialize_vectors()

/**
 * Disable all interrupts for a critical section.  The previous
 * level is returned in _level.
 */
#define _CPU_ISR_Disable( _level ) \
  (_level) = sparc_disable_interrupts()

/**
 * Enable interrupts to the previous level (returned by _CPU_ISR_Disable).
 * This indicates the end of a critical section.  The parameter
 * _level is not modified.
 */
#define _CPU_ISR_Enable( _level ) \
  sparc_enable_interrupts( _level )

/**
 * This temporarily restores the interrupt to _level before immediately
 * disabling them again.  This is used to divide long critical
 * sections into two or more parts.  The parameter _level is not
 * modified.
 */
#define _CPU_ISR_Flash( _level ) \
  sparc_flash_interrupts( _level )

#define _CPU_ISR_Is_enabled( _isr_cookie ) \
  sparc_interrupt_is_enabled( _isr_cookie )

RTEMS_INLINE_ROUTINE bool _CPU_ISR_Is_enabled( uint32_t level )
{
  return ( level & SPARC_PSR_PIL_MASK ) == 0;
}

/**
 * Map interrupt level in task mode onto the hardware that the CPU
 * actually provides.  Currently, interrupt levels which do not
 * map onto the CPU in a straight fashion are undefined.
 */
#define _CPU_ISR_Set_level( _newlevel ) \
   sparc_enable_interrupts( _newlevel << 8)

/**
 * @brief Obtain the current interrupt disable level.
 *
 * This method is invoked to return the current interrupt disable level.
 *
 * @return This method returns the current interrupt disable level.
 */
uint32_t   _CPU_ISR_Get_level( void );

/* end of ISR handler macros */

/* Context handler macros */

/**
 * Initialize the context to a state suitable for starting a
 * task after a context restore operation.  Generally, this
 * involves:
 *
 * - setting a starting address
 * - preparing the stack
 * - preparing the stack and frame pointers
 * - setting the proper interrupt level in the context
 * - initializing the floating point context
 *
 * @param[in] the_context points to the context area
 * @param[in] stack_base is the low address of the allocated stack area
 * @param[in] size is the size of the stack area in bytes
 * @param[in] new_level is the interrupt level for the task
 * @param[in] entry_point is the task's entry point
 * @param[in] is_fp is set to TRUE if the task is a floating point task
 * @param[in] tls_area is the thread-local storage (TLS) area
 *
 * NOTE:  Implemented as a subroutine for the SPARC port.
 */
void _CPU_Context_Initialize(
  Context_Control  *the_context,
  uint32_t         *stack_base,
  uint32_t          size,
  uint32_t          new_level,
  void             *entry_point,
  bool              is_fp,
  void             *tls_area
);

/**
 * This macro is invoked from _Thread_Handler to do whatever CPU
 * specific magic is required that must be done in the context of
 * the thread when it starts.
 *
 * On the SPARC, this is setting the frame pointer so GDB is happy.
 * Make GDB stop unwinding at _Thread_Handler, previous register window
 * Frame pointer is 0 and calling address must be a function with starting
 * with a SAVE instruction. If return address is leaf-function (no SAVE)
 * GDB will not look at prev reg window fp.
 *
 * _Thread_Handler is known to start with SAVE.
 */
#define _CPU_Context_Initialization_at_thread_begin() \
  do { \
    __asm__ volatile ("set _Thread_Handler,%%i7\n"::); \
  } while (0)

/**
 * This routine is responsible for somehow restarting the currently
 * executing task.
 *
 * On the SPARC, this is is relatively painless but requires a small
 * amount of wrapper code before using the regular restore code in
 * of the context switch.
 */
#define _CPU_Context_Restart_self( _the_context ) \
   _CPU_Context_restore( (_the_context) );

/**
 * @brief Nothing to do due to the synchronous or lazy floating point switch.
 */
#define _CPU_Context_Initialize_fp( _destination ) \
  do { } while ( 0 )

/**
 * @brief Nothing to do due to the synchronous or lazy floating point switch.
 */
#define _CPU_Context_save_fp( _fp_context_ptr ) \
  do { } while ( 0 )

/**
 * @brief Nothing to do due to the synchronous or lazy floating point switch.
 */
#define _CPU_Context_restore_fp( _fp_context_ptr ) \
  do { } while ( 0 )
/* end of Context handler macros */

/* Fatal Error manager macros */

/**
 * This routine copies _error into a known place -- typically a stack
 * location or a register, optionally disables interrupts, and
 * halts/stops the CPU.
 */
extern void _CPU_Fatal_halt(uint32_t source, uint32_t error)
  RTEMS_NO_RETURN;

/* end of Fatal Error manager macros */

/* Bitfield handler macros */

#if ( SPARC_HAS_BITSCAN == 0 )
  /**
   * The SPARC port uses the generic C algorithm for bitfield scan if the
   * CPU model does not have a scan instruction.
   */
  #define CPU_USE_GENERIC_BITFIELD_CODE TRUE
#else
  #error "scan instruction not currently supported by RTEMS!!"
#endif

/* end of Bitfield handler macros */

/* functions */

/**
 * @brief SPARC specific initialization.
 *
 * This routine performs CPU dependent initialization.
 */
void _CPU_Initialize(void);

/**
 * @brief SPARC specific raw ISR installer.
 *
 * This routine installs @a new_handler to be directly called from the trap
 * table.
 *
 * @param[in] vector is the vector number
 * @param[in] new_handler is the new ISR handler
 * @param[in] old_handler will contain the old ISR handler
 */
void _CPU_ISR_install_raw_handler(
  uint32_t    vector,
  proc_ptr    new_handler,
  proc_ptr   *old_handler
);

/**
 * @brief SPARC specific RTEMS ISR installer.
 *
 * This routine installs an interrupt vector.
 *
 * @param[in] vector is the vector number
 * @param[in] new_handler is the new ISR handler
 * @param[in] old_handler will contain the old ISR handler
 */

void _CPU_ISR_install_vector(
  uint32_t    vector,
  proc_ptr    new_handler,
  proc_ptr   *old_handler
);

/**
 * @brief SPARC specific context switch.
 *
 * This routine switches from the run context to the heir context.
 *
 * @param[in] run is the currently executing thread
 * @param[in] heir will become the currently executing thread
 */
void _CPU_Context_switch(
  Context_Control  *run,
  Context_Control  *heir
);

/**
 * @brief SPARC specific context restore.
 *
 * This routine is generally used only to restart self in an
 * efficient manner.
 *
 * @param[in] new_context is the context to restore
 */
void _CPU_Context_restore(
  Context_Control *new_context
) RTEMS_NO_RETURN;

#if defined(RTEMS_SMP)
  uint32_t _CPU_SMP_Initialize( void );

  bool _CPU_SMP_Start_processor( uint32_t cpu_index );

  void _CPU_SMP_Finalize_initialization( uint32_t cpu_count );

  void _CPU_SMP_Prepare_start_multitasking( void );

  #if defined(__leon__) && !defined(RTEMS_PARAVIRT)
    static inline uint32_t _CPU_SMP_Get_current_processor( void )
    {
      return _LEON3_Get_current_processor();
    }
  #else
    uint32_t _CPU_SMP_Get_current_processor( void );
  #endif

  void _CPU_SMP_Send_interrupt( uint32_t target_processor_index );

  static inline void _CPU_SMP_Processor_event_broadcast( void )
  {
    __asm__ volatile ( "" : : : "memory" );
  }

  static inline void _CPU_SMP_Processor_event_receive( void )
  {
    __asm__ volatile ( "" : : : "memory" );
  }
#endif

#if defined(SPARC_USE_LAZY_FP_SWITCH)
#define _CPU_Context_Destroy( _the_thread, _the_context ) \
  do { \
    Per_CPU_Control *cpu_self = _Per_CPU_Get(); \
    Thread_Control *_fp_owner = cpu_self->cpu_per_cpu.fp_owner; \
    if ( _fp_owner == _the_thread ) { \
      cpu_self->cpu_per_cpu.fp_owner = NULL; \
    } \
  } while ( 0 )
#endif

void _CPU_Context_volatile_clobber( uintptr_t pattern );

void _CPU_Context_validate( uintptr_t pattern );

typedef struct {
  uint32_t trap;
  CPU_Interrupt_frame *isf;
} CPU_Exception_frame;

void _CPU_Exception_frame_print( const CPU_Exception_frame *frame );

/**
 * @brief SPARC specific method to endian swap an uint32_t.
 *
 * The following routine swaps the endian format of an unsigned int.
 * It must be static because it is referenced indirectly.
 *
 * @param[in] value is the value to endian swap
 *
 * This version will work on any processor, but if you come across a better
 * way for the SPARC PLEASE use it.  The most common way to swap a 32-bit
 * entity as shown below is not any more efficient on the SPARC.
 *
 *    - swap least significant two bytes with 16-bit rotate
 *    - swap upper and lower 16-bits
 *    - swap most significant two bytes with 16-bit rotate
 *
 * It is not obvious how the SPARC can do significantly better than the
 * generic code.  gcc 2.7.0 only generates about 12 instructions for the
 * following code at optimization level four (i.e. -O4).
 */
static inline uint32_t CPU_swap_u32(
  uint32_t value
)
{
  uint32_t   byte1, byte2, byte3, byte4, swapped;

  byte4 = (value >> 24) & 0xff;
  byte3 = (value >> 16) & 0xff;
  byte2 = (value >> 8)  & 0xff;
  byte1 =  value        & 0xff;

  swapped = (byte1 << 24) | (byte2 << 16) | (byte3 << 8) | byte4;
  return( swapped );
}

/**
 * @brief SPARC specific method to endian swap an uint16_t.
 *
 * The following routine swaps the endian format of a uint16_t.
 *
 * @param[in] value is the value to endian swap
 */
#define CPU_swap_u16( value ) \
  (((value&0xff) << 8) | ((value >> 8)&0xff))

typedef uint32_t CPU_Counter_ticks;

uint32_t _CPU_Counter_frequency( void );

typedef CPU_Counter_ticks ( *SPARC_Counter_read )( void );

typedef CPU_Counter_ticks ( *SPARC_Counter_difference )(
  CPU_Counter_ticks second,
  CPU_Counter_ticks first
);

/*
 * The SPARC processors supported by RTEMS have no built-in CPU counter
 * support.  We have to use some hardware counter module for this purpose, for
 * example the GPTIMER instance used by the clock driver.  The BSP must provide
 * an implementation of the CPU counter read and difference functions.  This
 * allows the use of dynamic hardware enumeration.
 */
typedef struct {
  SPARC_Counter_read                counter_read;
  SPARC_Counter_difference          counter_difference;
  volatile const CPU_Counter_ticks *counter_address;
} SPARC_Counter;

extern const SPARC_Counter _SPARC_Counter;

static inline CPU_Counter_ticks _CPU_Counter_read( void )
{
  return ( *_SPARC_Counter.counter_read )();
}

static inline CPU_Counter_ticks _CPU_Counter_difference(
  CPU_Counter_ticks second,
  CPU_Counter_ticks first
)
{
  return ( *_SPARC_Counter.counter_difference )( second, first );
}

/** Type that can store a 32-bit integer or a pointer. */
typedef uintptr_t CPU_Uint32ptr;

#endif /* ASM */

#ifdef __cplusplus
}
#endif

#endif