source: rtems/cpukit/score/cpu/mips/rtems/score/cpu.h @ 3b1c100

/*
 *  Mips CPU Dependent Header File
 *
 *  Conversion to MIPS port by Alan Cudmore <alanc@linuxstart.com> and
 *           Joel Sherrill <joel@OARcorp.com>.
 *
 *    These changes made the code conditional on standard cpp predefines,
 *    merged the mips1 and mips3 code sequences as much as possible,
 *    and moved some of the assembly code to C.  Alan did much of the
 *    initial analysis and rework.  Joel took over from there and
 *    wrote the JMR3904 BSP so this could be tested.  Joel also
 *    added the new interrupt vectoring support in libcpu and
 *    tried to better support the various interrupt controllers.
 *
 *  Original MIP64ORION port by Craig Lebakken <craigl@transition.com>
 *           COPYRIGHT (c) 1996 by Transition Networks Inc.
 *
 *    To anyone who acknowledges that this file is provided "AS IS"
 *    without any express or implied warranty:
 *      permission to use, copy, modify, and distribute this file
 *      for any purpose is hereby granted without fee, provided that
 *      the above copyright notice and this notice appears in all
 *      copies, and that the name of Transition Networks not be used in
 *      advertising or publicity pertaining to distribution of the
 *      software without specific, written prior permission.
 *      Transition Networks makes no representations about the suitability
 *      of this software for any purpose.
 *
 *  COPYRIGHT (c) 1989-2001.
 *  On-Line Applications Research Corporation (OAR).
 *
 *  The license and distribution terms for this file may be
 *  found in the file LICENSE in this distribution or at
 *  http://www.rtems.com/license/LICENSE.
 *
 *  $Id$
 */

#ifndef __CPU_h
#define __CPU_h

#ifdef __cplusplus
extern "C" {
#endif

#include <rtems/score/mips.h>       /* pick up machine definitions */
#ifndef ASM
#include <rtems/score/types.h>
#endif

/* conditional compilation parameters */

/*
 *  Should the calls to _Thread_Enable_dispatch be inlined?
 *
 *  If TRUE, then they are inlined.
 *  If FALSE, then a subroutine call is made.
 *
 *  Basically this is an example of the classic trade-off of size
 *  versus speed.  Inlining the call (TRUE) typically increases the
 *  size of RTEMS while speeding up the enabling of dispatching.
 *  [NOTE: In general, the _Thread_Dispatch_disable_level will
 *  only be 0 or 1 unless you are in an interrupt handler and that
 *  interrupt handler invokes the executive.]  When not inlined
 *  something calls _Thread_Enable_dispatch which in turns calls
 *  _Thread_Dispatch.  If the enable dispatch is inlined, then
 *  one subroutine call is avoided entirely.]
 */

#define CPU_INLINE_ENABLE_DISPATCH       FALSE

/*
 *  Should the body of the search loops in _Thread_queue_Enqueue_priority
 *  be unrolled one time?  In unrolled each iteration of the loop examines
 *  two "nodes" on the chain being searched.  Otherwise, only one node
 *  is examined per iteration.
 *
 *  If TRUE, then the loops are unrolled.
 *  If FALSE, then the loops are not unrolled.
 *
 *  The primary factor in making this decision is the cost of disabling
 *  and enabling interrupts (_ISR_Flash) versus the cost of rest of the
 *  body of the loop.  On some CPUs, the flash is more expensive than
 *  one iteration of the loop body.  In this case, it might be desirable
 *  to unroll the loop.  It is important to note that on some CPUs, this
 *  code is the longest interrupt disable period in RTEMS.  So it is
 *  necessary to strike a balance when setting this parameter.
 */

#define CPU_UNROLL_ENQUEUE_PRIORITY      TRUE

/*
 *  Does RTEMS manage a dedicated interrupt stack in software?
 *
 *  If TRUE, then a stack is allocated in _Interrupt_Manager_initialization.
 *  If FALSE, nothing is done.
 *
 *  If the CPU supports a dedicated interrupt stack in hardware,
 *  then it is generally the responsibility of the BSP to allocate it
 *  and set it up.
 *
 *  If the CPU does not support a dedicated interrupt stack, then
 *  the porter has two options: (1) execute interrupts on the
 *  stack of the interrupted task, and (2) have RTEMS manage a dedicated
 *  interrupt stack.
 *
 *  If this is TRUE, CPU_ALLOCATE_INTERRUPT_STACK should also be TRUE.
 *
 *  Only one of CPU_HAS_SOFTWARE_INTERRUPT_STACK and
 *  CPU_HAS_HARDWARE_INTERRUPT_STACK should be set to TRUE.  It is
 *  possible that both are FALSE for a particular CPU.  Although it
 *  is unclear what that would imply about the interrupt processing
 *  procedure on that CPU.
 */

#define CPU_HAS_SOFTWARE_INTERRUPT_STACK FALSE

/*
 *  Does this CPU have hardware support for a dedicated interrupt stack?
 *
 *  If TRUE, then it must be installed during initialization.
 *  If FALSE, then no installation is performed.
 *
 *  If this is TRUE, CPU_ALLOCATE_INTERRUPT_STACK should also be TRUE.
 *
 *  Only one of CPU_HAS_SOFTWARE_INTERRUPT_STACK and
 *  CPU_HAS_HARDWARE_INTERRUPT_STACK should be set to TRUE.  It is
 *  possible that both are FALSE for a particular CPU.  Although it
 *  is unclear what that would imply about the interrupt processing
 *  procedure on that CPU.
 */

#define CPU_HAS_HARDWARE_INTERRUPT_STACK FALSE

/*
 *  Does RTEMS allocate a dedicated interrupt stack in the Interrupt Manager?
 *
 *  If TRUE, then the memory is allocated during initialization.
 *  If FALSE, then the memory is allocated during initialization.
 *
 *  This should be TRUE is CPU_HAS_SOFTWARE_INTERRUPT_STACK is TRUE
 *  or CPU_INSTALL_HARDWARE_INTERRUPT_STACK is TRUE.
 */

#define CPU_ALLOCATE_INTERRUPT_STACK FALSE

/*
 *  Does the RTEMS invoke the user's ISR with the vector number and
 *  a pointer to the saved interrupt frame (1) or just the vector
 *  number (0)?
 *
 */

#define CPU_ISR_PASSES_FRAME_POINTER 1



/*
 *  Does the CPU have hardware floating point?
 *
 *  If TRUE, then the RTEMS_FLOATING_POINT task attribute is supported.
 *  If FALSE, then the RTEMS_FLOATING_POINT task attribute is ignored.
 *
 *  If there is a FP coprocessor such as the i387 or mc68881, then
 *  the answer is TRUE.
 *
 *  The macro name "MIPS_HAS_FPU" should be made CPU specific.
 *  It indicates whether or not this CPU model has FP support.  For
 *  example, it would be possible to have an i386_nofp CPU model
 *  which set this to false to indicate that you have an i386 without
 *  an i387 and wish to leave floating point support out of RTEMS.
 */

#if ( MIPS_HAS_FPU == 1 )
#define CPU_HARDWARE_FP     TRUE
#else
#define CPU_HARDWARE_FP     FALSE
#endif

/*
 *  Are all tasks RTEMS_FLOATING_POINT tasks implicitly?
 *
 *  If TRUE, then the RTEMS_FLOATING_POINT task attribute is assumed.
 *  If FALSE, then the RTEMS_FLOATING_POINT task attribute is followed.
 *
 *  If CPU_HARDWARE_FP is FALSE, then this should be FALSE as well.
 */

#define CPU_ALL_TASKS_ARE_FP    FALSE

/*
 *  Should the IDLE task have a floating point context?
 *
 *  If TRUE, then the IDLE task is created as a RTEMS_FLOATING_POINT task
 *  and it has a floating point context which is switched in and out.
 *  If FALSE, then the IDLE task does not have a floating point context.
 *
 *  Setting this to TRUE negatively impacts the time required to preempt
 *  the IDLE task from an interrupt because the floating point context
 *  must be saved as part of the preemption.
 */

#define CPU_IDLE_TASK_IS_FP      FALSE

/*
 *  Should the saving of the floating point registers be deferred
 *  until a context switch is made to another different floating point
 *  task?
 *
 *  If TRUE, then the floating point context will not be stored until
 *  necessary.  It will remain in the floating point registers and not
 *  disturned until another floating point task is switched to.
 *
 *  If FALSE, then the floating point context is saved when a floating
 *  point task is switched out and restored when the next floating point
 *  task is restored.  The state of the floating point registers between
 *  those two operations is not specified.
 *
 *  If the floating point context does NOT have to be saved as part of
 *  interrupt dispatching, then it should be safe to set this to TRUE.
 *
 *  Setting this flag to TRUE results in using a different algorithm
 *  for deciding when to save and restore the floating point context.
 *  The deferred FP switch algorithm minimizes the number of times
 *  the FP context is saved and restored.  The FP context is not saved
 *  until a context switch is made to another, different FP task.
 *  Thus in a system with only one FP task, the FP context will never
 *  be saved or restored.
 */

#define CPU_USE_DEFERRED_FP_SWITCH       TRUE

/*
 *  Does this port provide a CPU dependent IDLE task implementation?
 *
 *  If TRUE, then the routine _CPU_Internal_threads_Idle_thread_body
 *  must be provided and is the default IDLE thread body instead of
 *  _Internal_threads_Idle_thread_body.
 *
 *  If FALSE, then use the generic IDLE thread body if the BSP does
 *  not provide one.
 *
 *  This is intended to allow for supporting processors which have
 *  a low power or idle mode.  When the IDLE thread is executed, then
 *  the CPU can be powered down.
 *
 *  The order of precedence for selecting the IDLE thread body is:
 *
 *    1.  BSP provided
 *    2.  CPU dependent (if provided)
 *    3.  generic (if no BSP and no CPU dependent)
 */

/* we can use the low power wait instruction for the IDLE thread */
#define CPU_PROVIDES_IDLE_THREAD_BODY    TRUE

/*
 *  Does the stack grow up (toward higher addresses) or down
 *  (toward lower addresses)?
 *
 *  If TRUE, then the grows upward.
 *  If FALSE, then the grows toward smaller addresses.
 */

/* our stack grows down */
#define CPU_STACK_GROWS_UP               FALSE

/*
 *  The following is the variable attribute used to force alignment
 *  of critical RTEMS structures.  On some processors it may make
 *  sense to have these aligned on tighter boundaries than
 *  the minimum requirements of the compiler in order to have as
 *  much of the critical data area as possible in a cache line.
 *
 *  The placement of this macro in the declaration of the variables
 *  is based on the syntactically requirements of the GNU C
 *  "__attribute__" extension.  For example with GNU C, use
 *  the following to force a structures to a 32 byte boundary.
 *
 *      __attribute__ ((aligned (32)))
 *
 *  NOTE:  Currently only the Priority Bit Map table uses this feature.
 *         To benefit from using this, the data must be heavily
 *         used so it will stay in the cache and used frequently enough
 *         in the executive to justify turning this on.
 */

/* our cache line size is 16 bytes */
#if __GNUC__
#define CPU_STRUCTURE_ALIGNMENT __attribute__ ((aligned (16)))
#else
#define CPU_STRUCTURE_ALIGNMENT
#endif

/*
 *  Define what is required to specify how the network to host conversion
 *  routines are handled.
 */

#define CPU_HAS_OWN_HOST_TO_NETWORK_ROUTINES     FALSE
#define CPU_BIG_ENDIAN                           TRUE
#define CPU_LITTLE_ENDIAN                        FALSE

/*
 *  The following defines the number of bits actually used in the
 *  interrupt field of the task mode.  How those bits map to the
 *  CPU interrupt levels is defined by the routine _CPU_ISR_Set_level().
 */

#define CPU_MODES_INTERRUPT_MASK   0x000000ff

/*
 *  Processor defined structures
 *
 *  Examples structures include the descriptor tables from the i386
 *  and the processor control structure on the i960ca.
 */

/* may need to put some structures here.  */

/*
 * Contexts
 *
 *  Generally there are 2 types of context to save.
 *     1. Interrupt registers to save
 *     2. Task level registers to save
 *
 *  This means we have the following 3 context items:
 *     1. task level context stuff::  Context_Control
 *     2. floating point task stuff:: Context_Control_fp
 *     3. special interrupt level context :: Context_Control_interrupt
 *
 *  On some processors, it is cost-effective to save only the callee
 *  preserved registers during a task context switch.  This means
 *  that the ISR code needs to save those registers which do not
 *  persist across function calls.  It is not mandatory to make this
 *  distinctions between the caller/callee saves registers for the
 *  purpose of minimizing context saved during task switch and on interrupts.
 *  If the cost of saving extra registers is minimal, simplicity is the
 *  choice.  Save the same context on interrupt entry as for tasks in
 *  this case.
 *
 *  Additionally, if gdb is to be made aware of RTEMS tasks for this CPU, then
 *  care should be used in designing the context area.
 *
 *  On some CPUs with hardware floating point support, the Context_Control_fp
 *  structure will not be used or it simply consist of an array of a
 *  fixed number of bytes.   This is done when the floating point context
 *  is dumped by a "FP save context" type instruction and the format
 *  is not really defined by the CPU.  In this case, there is no need
 *  to figure out the exact format -- only the size.  Of course, although
 *  this is enough information for RTEMS, it is probably not enough for
 *  a debugger such as gdb.  But that is another problem.
 */

#ifndef ASSEMBLY_ONLY

/* WARNING: If this structure is modified, the constants in cpu.h must be updated. */
#if __mips == 1
#define __MIPS_REGISTER_TYPE     unsigned32
#define __MIPS_FPU_REGISTER_TYPE unsigned32
#elif __mips == 3
#define __MIPS_REGISTER_TYPE     unsigned64
#define __MIPS_FPU_REGISTER_TYPE unsigned64
#else
#error "mips register size: unknown architecture level!!"
#endif
typedef struct {
    __MIPS_REGISTER_TYPE s0;
    __MIPS_REGISTER_TYPE s1;
    __MIPS_REGISTER_TYPE s2;
    __MIPS_REGISTER_TYPE s3;
    __MIPS_REGISTER_TYPE s4;
    __MIPS_REGISTER_TYPE s5;
    __MIPS_REGISTER_TYPE s6;
    __MIPS_REGISTER_TYPE s7;
    __MIPS_REGISTER_TYPE sp;
    __MIPS_REGISTER_TYPE fp;
    __MIPS_REGISTER_TYPE ra;
    __MIPS_REGISTER_TYPE c0_sr;
    __MIPS_REGISTER_TYPE c0_epc;
} Context_Control;

/* WARNING: If this structure is modified, the constants in cpu.h
 *          must also be updated.
 */

typedef struct {
#if ( CPU_HARDWARE_FP == TRUE )
    __MIPS_FPU_REGISTER_TYPE fp0;
    __MIPS_FPU_REGISTER_TYPE fp1;
    __MIPS_FPU_REGISTER_TYPE fp2;
    __MIPS_FPU_REGISTER_TYPE fp3;
    __MIPS_FPU_REGISTER_TYPE fp4;
    __MIPS_FPU_REGISTER_TYPE fp5;
    __MIPS_FPU_REGISTER_TYPE fp6;
    __MIPS_FPU_REGISTER_TYPE fp7;
    __MIPS_FPU_REGISTER_TYPE fp8;
    __MIPS_FPU_REGISTER_TYPE fp9;
    __MIPS_FPU_REGISTER_TYPE fp10;
    __MIPS_FPU_REGISTER_TYPE fp11;
    __MIPS_FPU_REGISTER_TYPE fp12;
    __MIPS_FPU_REGISTER_TYPE fp13;
    __MIPS_FPU_REGISTER_TYPE fp14;
    __MIPS_FPU_REGISTER_TYPE fp15;
    __MIPS_FPU_REGISTER_TYPE fp16;
    __MIPS_FPU_REGISTER_TYPE fp17;
    __MIPS_FPU_REGISTER_TYPE fp18;
    __MIPS_FPU_REGISTER_TYPE fp19;
    __MIPS_FPU_REGISTER_TYPE fp20;
    __MIPS_FPU_REGISTER_TYPE fp21;
    __MIPS_FPU_REGISTER_TYPE fp22;
    __MIPS_FPU_REGISTER_TYPE fp23;
    __MIPS_FPU_REGISTER_TYPE fp24;
    __MIPS_FPU_REGISTER_TYPE fp25;
    __MIPS_FPU_REGISTER_TYPE fp26;
    __MIPS_FPU_REGISTER_TYPE fp27;
    __MIPS_FPU_REGISTER_TYPE fp28;
    __MIPS_FPU_REGISTER_TYPE fp29;
    __MIPS_FPU_REGISTER_TYPE fp30;
    __MIPS_FPU_REGISTER_TYPE fp31;
#endif
} Context_Control_fp;

/*
 *  This struct reflects the stack frame employed in ISR_Handler.  Note
 *  that the ISR routine save some of the registers to this frame for
 *  all interrupts and exceptions.  Other registers are saved only on
 *  exceptions, while others are not touched at all.  The untouched 
 *  registers are not normally disturbed by high-level language 
 *  programs so they can be accessed when required.
 *
 *  The registers and their ordering in this struct must directly
 *  correspond to the layout and ordering of * shown in iregdef.h,
 *  as cpu_asm.S uses those definitions to fill the stack frame.  
 *  This struct provides access to the stack frame for C code.
 *
 *  Similarly, this structure is used by debugger stubs and exception
 *  processing routines so be careful when changing the format.
 *
 *  NOTE: The comments with this structure and cpu_asm.S should be kept
 *        in sync.  When in doubt, look in the  code to see if the
 *        registers you're interested in are actually treated as expected.
 *        The order of the first portion of this structure follows the
 *        order of registers expected by gdb.
 */

typedef struct
{
  __MIPS_REGISTER_TYPE  r0;       /*  0 -- NOT FILLED IN */
  __MIPS_REGISTER_TYPE  at;       /*  1 -- saved always */
  __MIPS_REGISTER_TYPE  v0;       /*  2 -- saved always */
  __MIPS_REGISTER_TYPE  v1;       /*  3 -- saved always */
  __MIPS_REGISTER_TYPE  a0;       /*  4 -- saved always */
  __MIPS_REGISTER_TYPE  a1;       /*  5 -- saved always */
  __MIPS_REGISTER_TYPE  a2;       /*  6 -- saved always */
  __MIPS_REGISTER_TYPE  a3;       /*  7 -- saved always */
  __MIPS_REGISTER_TYPE  t0;       /*  8 -- saved always */
  __MIPS_REGISTER_TYPE  t1;       /*  9 -- saved always */
  __MIPS_REGISTER_TYPE  t2;       /* 10 -- saved always */
  __MIPS_REGISTER_TYPE  t3;       /* 11 -- saved always */
  __MIPS_REGISTER_TYPE  t4;       /* 12 -- saved always */
  __MIPS_REGISTER_TYPE  t5;       /* 13 -- saved always */
  __MIPS_REGISTER_TYPE  t6;       /* 14 -- saved always */
  __MIPS_REGISTER_TYPE  t7;       /* 15 -- saved always */
  __MIPS_REGISTER_TYPE  s0;       /* 16 -- saved on exceptions */
  __MIPS_REGISTER_TYPE  s1;       /* 17 -- saved on exceptions */
  __MIPS_REGISTER_TYPE  s2;       /* 18 -- saved on exceptions */
  __MIPS_REGISTER_TYPE  s3;       /* 19 -- saved on exceptions */
  __MIPS_REGISTER_TYPE  s4;       /* 20 -- saved on exceptions */
  __MIPS_REGISTER_TYPE  s5;       /* 21 -- saved on exceptions */
  __MIPS_REGISTER_TYPE  s6;       /* 22 -- saved on exceptions */
  __MIPS_REGISTER_TYPE  s7;       /* 23 -- saved on exceptions */
  __MIPS_REGISTER_TYPE  t8;       /* 24 -- saved always */
  __MIPS_REGISTER_TYPE  t9;       /* 25 -- saved always */
  __MIPS_REGISTER_TYPE  k0;       /* 26 -- NOT FILLED IN, kernel tmp reg */
  __MIPS_REGISTER_TYPE  k1;       /* 27 -- NOT FILLED IN, kernel tmp reg */
  __MIPS_REGISTER_TYPE  gp;       /* 28 -- saved always */
  __MIPS_REGISTER_TYPE  sp;       /* 29 -- saved on exceptions NOT RESTORED */
  __MIPS_REGISTER_TYPE  fp;       /* 30 -- saved always */
  __MIPS_REGISTER_TYPE  ra;       /* 31 -- saved always */
  __MIPS_REGISTER_TYPE  c0_sr;    /* 32 -- saved always, some bits are */
                                  /*    manipulated per-thread          */
  __MIPS_REGISTER_TYPE  mdlo;     /* 33 -- saved always */
  __MIPS_REGISTER_TYPE  mdhi;     /* 34 -- saved always */
  __MIPS_REGISTER_TYPE  badvaddr; /* 35 -- saved on exceptions, read-only */
  __MIPS_REGISTER_TYPE  cause;    /* 36 -- saved on exceptions NOT restored */
  __MIPS_REGISTER_TYPE  epc;      /* 37 -- saved always, read-only register */
                                  /*        but logically restored */
  __MIPS_FPU_REGISTER_TYPE f0;    /* 38 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f1;    /* 39 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f2;    /* 40 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f3;    /* 41 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f4;    /* 42 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f5;    /* 43 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f6;    /* 44 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f7;    /* 45 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f8;    /* 46 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f9;    /* 47 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f10;   /* 48 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f11;   /* 49 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f12;   /* 50 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f13;   /* 51 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f14;   /* 52 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f15;   /* 53 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f16;   /* 54 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f17;   /* 55 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f18;   /* 56 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f19;   /* 57 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f20;   /* 58 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f21;   /* 59 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f22;   /* 60 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f23;   /* 61 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f24;   /* 62 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f25;   /* 63 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f26;   /* 64 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f27;   /* 65 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f28;   /* 66 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f29;   /* 67 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f30;   /* 68 -- saved if FP enabled */
  __MIPS_FPU_REGISTER_TYPE f31;   /* 69 -- saved if FP enabled */
  __MIPS_REGISTER_TYPE     fcsr;  /* 70 -- saved on exceptions */
                                  /*    (oddly not documented on MGV) */
  __MIPS_REGISTER_TYPE     feir;  /* 71 -- saved on exceptions */
                                  /*    (oddly not documented on MGV) */

  /* GDB does not seem to care about anything past this point */

  __MIPS_REGISTER_TYPE  tlbhi;    /* 72 - NOT FILLED IN, doesn't exist on */
                                  /*         all MIPS CPUs (at least MGV) */
#if __mips == 1
  __MIPS_REGISTER_TYPE  tlblo;    /* 73 - NOT FILLED IN, doesn't exist on */
                                  /*         all MIPS CPUs (at least MGV) */
#endif
#if  __mips == 3
  __MIPS_REGISTER_TYPE  tlblo0;   /* 73 - NOT FILLED IN, doesn't exist on */
                                  /*         all MIPS CPUs (at least MGV) */
#endif

  __MIPS_REGISTER_TYPE  inx;      /* 74 -- NOT FILLED IN, doesn't exist on */
                                  /*         all MIPS CPUs (at least MGV) */
  __MIPS_REGISTER_TYPE  rand;     /* 75 -- NOT FILLED IN, doesn't exist on */
                                  /*         all MIPS CPUs (at least MGV) */
  __MIPS_REGISTER_TYPE  ctxt;     /* 76 -- NOT FILLED IN, doesn't exist on */
                                  /*         all MIPS CPUs (at least MGV) */
  __MIPS_REGISTER_TYPE  exctype;  /* 77 -- NOT FILLED IN (not enough info) */
  __MIPS_REGISTER_TYPE  mode;     /* 78 -- NOT FILLED IN (not enough info) */
  __MIPS_REGISTER_TYPE  prid;     /* 79 -- NOT FILLED IN (not need to do so) */
  __MIPS_REGISTER_TYPE  tar ;     /* 80 -- target address register, filled on exceptions */
  /* end of __mips == 1 so NREGS == 81 */
#if  __mips == 3
  __MIPS_REGISTER_TYPE  tlblo1;   /* 81 -- NOT FILLED IN */
  __MIPS_REGISTER_TYPE  pagemask; /* 82 -- NOT FILLED IN */
  __MIPS_REGISTER_TYPE  wired;    /* 83 -- NOT FILLED IN */
  __MIPS_REGISTER_TYPE  count;    /* 84 -- NOT FILLED IN */
  __MIPS_REGISTER_TYPE  compare;  /* 85 -- NOT FILLED IN */
  __MIPS_REGISTER_TYPE  config;   /* 86 -- NOT FILLED IN */
  __MIPS_REGISTER_TYPE  lladdr;   /* 87 -- NOT FILLED IN */
  __MIPS_REGISTER_TYPE  watchlo;  /* 88 -- NOT FILLED IN */
  __MIPS_REGISTER_TYPE  watchhi;  /* 89 -- NOT FILLED IN */
  __MIPS_REGISTER_TYPE  ecc;      /* 90 -- NOT FILLED IN */
  __MIPS_REGISTER_TYPE  cacheerr; /* 91 -- NOT FILLED IN */
  __MIPS_REGISTER_TYPE  taglo;    /* 92 -- NOT FILLED IN */
  __MIPS_REGISTER_TYPE  taghi;    /* 93 -- NOT FILLED IN */
  __MIPS_REGISTER_TYPE  errpc;    /* 94 -- NOT FILLED IN */
  __MIPS_REGISTER_TYPE  xctxt;    /* 95 -- NOT FILLED IN */
 /* end of __mips == 3 so NREGS == 96 */
#endif

} CPU_Interrupt_frame;


/*
 *  The following table contains the information required to configure
 *  the mips processor specific parameters.
 */

typedef struct {
  void       (*pretasking_hook)( void );
  void       (*predriver_hook)( void );
  void       (*postdriver_hook)( void );
  void       (*idle_task)( void );
  boolean      do_zero_of_workspace;
  unsigned32   idle_task_stack_size;
  unsigned32   interrupt_stack_size;
  unsigned32   extra_mpci_receive_server_stack;
  void *     (*stack_allocate_hook)( unsigned32 );
  void       (*stack_free_hook)( void* );
  /* end of fields required on all CPUs */

  unsigned32   clicks_per_microsecond;
}   rtems_cpu_table;


/*
 *  Macros to access required entires in the CPU Table are in
 *  the file rtems/system.h.
 */

/*
 *  Macros to access MIPS specific additions to the CPU Table
 */

#define rtems_cpu_configuration_get_clicks_per_microsecond() \
   (_CPU_Table.clicks_per_microsecond)

/*
 *  This variable is optional.  It is used on CPUs on which it is difficult
 *  to generate an "uninitialized" FP context.  It is filled in by
 *  _CPU_Initialize and copied into the task's FP context area during
 *  _CPU_Context_Initialize.
 */

SCORE_EXTERN Context_Control_fp  _CPU_Null_fp_context;

/*
 *  On some CPUs, RTEMS supports a software managed interrupt stack.
 *  This stack is allocated by the Interrupt Manager and the switch
 *  is performed in _ISR_Handler.  These variables contain pointers
 *  to the lowest and highest addresses in the chunk of memory allocated
 *  for the interrupt stack.  Since it is unknown whether the stack
 *  grows up or down (in general), this give the CPU dependent
 *  code the option of picking the version it wants to use.
 *
 *  NOTE: These two variables are required if the macro
 *        CPU_HAS_SOFTWARE_INTERRUPT_STACK is defined as TRUE.
 */

SCORE_EXTERN void               *_CPU_Interrupt_stack_low;
SCORE_EXTERN void               *_CPU_Interrupt_stack_high;

/*
 *  With some compilation systems, it is difficult if not impossible to
 *  call a high-level language routine from assembly language.  This
 *  is especially true of commercial Ada compilers and name mangling
 *  C++ ones.  This variable can be optionally defined by the CPU porter
 *  and contains the address of the routine _Thread_Dispatch.  This
 *  can make it easier to invoke that routine at the end of the interrupt
 *  sequence (if a dispatch is necessary).
 *

SCORE_EXTERN void           (*_CPU_Thread_dispatch_pointer)();
 *
 *  NOTE: Not needed on this port.
 */



/*
 *  Nothing prevents the porter from declaring more CPU specific variables.
 */

/* XXX: if needed, put more variables here */

/*
 *  The size of the floating point context area.  On some CPUs this
 *  will not be a "sizeof" because the format of the floating point
 *  area is not defined -- only the size is.  This is usually on
 *  CPUs with a "floating point save context" instruction.
 */

#define CPU_CONTEXT_FP_SIZE sizeof( Context_Control_fp )

/*
 *  Amount of extra stack (above minimum stack size) required by
 *  system initialization thread.  Remember that in a multiprocessor
 *  system the system intialization thread becomes the MP server thread.
 */

#define CPU_MPCI_RECEIVE_SERVER_EXTRA_STACK 0

/*
 *  This defines the number of entries in the ISR_Vector_table managed
 *  by RTEMS.
 */

extern unsigned int mips_interrupt_number_of_vectors;
#define CPU_INTERRUPT_NUMBER_OF_VECTORS      (mips_interrupt_number_of_vectors)
#define CPU_INTERRUPT_MAXIMUM_VECTOR_NUMBER  (CPU_INTERRUPT_NUMBER_OF_VECTORS - 1)

/*
 *  Should be large enough to run all RTEMS tests.  This insures
 *  that a "reasonable" small application should not have any problems.
 */

#define CPU_STACK_MINIMUM_SIZE          (2048*sizeof(unsigned32))


/*
 *  CPU's worst alignment requirement for data types on a byte boundary.  This
 *  alignment does not take into account the requirements for the stack.
 */

#define CPU_ALIGNMENT              8

/*
 *  This number corresponds to the byte alignment requirement for the
 *  heap handler.  This alignment requirement may be stricter than that
 *  for the data types alignment specified by CPU_ALIGNMENT.  It is
 *  common for the heap to follow the same alignment requirement as
 *  CPU_ALIGNMENT.  If the CPU_ALIGNMENT is strict enough for the heap,
 *  then this should be set to CPU_ALIGNMENT.
 *
 *  NOTE:  This does not have to be a power of 2.  It does have to
 *         be greater or equal to than CPU_ALIGNMENT.
 */

#define CPU_HEAP_ALIGNMENT         CPU_ALIGNMENT

/*
 *  This number corresponds to the byte alignment requirement for memory
 *  buffers allocated by the partition manager.  This alignment requirement
 *  may be stricter than that for the data types alignment specified by
 *  CPU_ALIGNMENT.  It is common for the partition to follow the same
 *  alignment requirement as CPU_ALIGNMENT.  If the CPU_ALIGNMENT is strict
 *  enough for the partition, then this should be set to CPU_ALIGNMENT.
 *
 *  NOTE:  This does not have to be a power of 2.  It does have to
 *         be greater or equal to than CPU_ALIGNMENT.
 */

#define CPU_PARTITION_ALIGNMENT    CPU_ALIGNMENT

/*
 *  This number corresponds to the byte alignment requirement for the
 *  stack.  This alignment requirement may be stricter than that for the
 *  data types alignment specified by CPU_ALIGNMENT.  If the CPU_ALIGNMENT
 *  is strict enough for the stack, then this should be set to 0.
 *
 *  NOTE:  This must be a power of 2 either 0 or greater than CPU_ALIGNMENT.
 */

#define CPU_STACK_ALIGNMENT        CPU_ALIGNMENT

/*
 *  ISR handler macros
 */

/*
 *  Support routine to initialize the RTEMS vector table after it is allocated.
 */

#define _CPU_Initialize_vectors()

/*
 *  Disable all interrupts for an RTEMS critical section.  The previous
 *  level is returned in _level.
 */

#define _CPU_ISR_Disable( _level ) \
  do { \
    unsigned int _scratch; \
    mips_get_sr( _scratch ); \
    mips_set_sr( _scratch & ~SR_INTERRUPT_ENABLE_BITS ); \
    _level = _scratch & SR_INTERRUPT_ENABLE_BITS; \
  } while(0)

/*
 *  Enable interrupts to the previous level (returned by _CPU_ISR_Disable).
 *  This indicates the end of an RTEMS critical section.  The parameter
 *  _level is not modified.
 */

#define _CPU_ISR_Enable( _level )  \
  do { \
    unsigned int _scratch; \
    mips_get_sr( _scratch ); \
    mips_set_sr( (_scratch & ~SR_INTERRUPT_ENABLE_BITS) | (_level & SR_INTERRUPT_ENABLE_BITS) ); \
  } while(0)

/*
 *  This temporarily restores the interrupt to _level before immediately
 *  disabling them again.  This is used to divide long RTEMS critical
 *  sections into two or more parts.  The parameter _level is not
 *  modified.
 */

#define _CPU_ISR_Flash( _xlevel ) \
  do { \
    unsigned int _scratch2 = _xlevel; \
    _CPU_ISR_Enable( _scratch2 ); \
    _CPU_ISR_Disable( _scratch2 ); \
    _xlevel = _scratch2; \
  } while(0)

/*
 *  Map interrupt level in task mode onto the hardware that the CPU
 *  actually provides.  Currently, interrupt levels which do not
 *  map onto the CPU in a generic fashion are undefined.  Someday,
 *  it would be nice if these were "mapped" by the application
 *  via a callout.  For example, m68k has 8 levels 0 - 7, levels
 *  8 - 255 would be available for bsp/application specific meaning.
 *  This could be used to manage a programmable interrupt controller
 *  via the rtems_task_mode directive.
 *
 *  On the MIPS, 0 is all on.  Non-zero is all off.  This only
 *  manipulates the IEC.
 */

unsigned32 _CPU_ISR_Get_level( void );  /* in cpu.c */

void _CPU_ISR_Set_level( unsigned32 );  /* in cpu.c */

/* end of ISR handler macros */

/* Context handler macros */

/*
 *  Initialize the context to a state suitable for starting a
 *  task after a context restore operation.  Generally, this
 *  involves:
 *
 *     - setting a starting address
 *     - preparing the stack
 *     - preparing the stack and frame pointers
 *     - setting the proper interrupt level in the context
 *     - initializing the floating point context
 *
 *  This routine generally does not set any unnecessary register
 *  in the context.  The state of the "general data" registers is
 *  undefined at task start time.
 *
 *  NOTE: This is_fp parameter is TRUE if the thread is to be a floating
 *        point thread.  This is typically only used on CPUs where the
 *        FPU may be easily disabled by software such as on the SPARC
 *        where the PSR contains an enable FPU bit.
 *
 *  The per-thread status register holds the interrupt enable, FP enable
 *  and global interrupt enable for that thread.  It means each thread can
 *  enable its own set of interrupts.  If interrupts are disabled, RTEMS
 *  can still dispatch via blocking calls.  This is the function of the 
 *  "Interrupt Level", and on the MIPS, it controls the IEC bit and all 
 *  the hardware interrupts as defined in the SR.  Software ints
 *  are automatically enabled for all threads, as they will only occur under 
 *  program control anyhow.  Besides, the interrupt level parm is only 8 bits, 
 *  and controlling the software ints plus the others would require 9.
 *
 *  If the Interrupt Level is 0, all ints are on.  Otherwise, the 
 *  Interrupt Level should supply a bit pattern to impose on the SR 
 *  interrupt bits; bit 0 applies to the mips1 IEC bit/mips3 EXL&IE, bits 1 thru 6
 *  apply to the SR register Intr bits from bit 10 thru bit 15.  Bit 7 of 
 *  the Interrupt Level parameter is unused at this time.
 *
 *  These are the only per-thread SR bits, the others are maintained
 *  globally & explicitly preserved by the Context Switch code in cpu_asm.s
 */


#if __mips == 3
#define _INTON  (SR_EXL | SR_IE)
#define _EXTRABITS      0
#endif
#if __mips == 1
#define _INTON          SR_IEC
#define _EXTRABITS      0  /* make sure we're in user mode on MIPS1 processors */
#endif

#define _CPU_Context_Initialize( _the_context, _stack_base, _size, _isr, _entry_point, _is_fp ) \
  { \
        unsigned32 _stack_tmp = \
           (unsigned32)(_stack_base) + (_size) - CPU_STACK_ALIGNMENT; \
        unsigned32 _intlvl = _isr & 0xff; \
        _stack_tmp &= ~(CPU_STACK_ALIGNMENT - 1); \
        (_the_context)->sp = _stack_tmp; \
        (_the_context)->fp = _stack_tmp; \
        (_the_context)->ra = (unsigned64)_entry_point; \
        (_the_context)->c0_sr = ((_intlvl==0)?(0xFF00 | _INTON):( ((_intlvl<<9) & 0xfc00) | \
                                                       0x300 | \
                                                       ((_intlvl & 1)?_INTON:0)) ) | \
                                SR_CU0 | ((_is_fp)?SR_CU1:0) | _EXTRABITS; \
  }



/*
 *  This routine is responsible for somehow restarting the currently
 *  executing task.  If you are lucky, then all that is necessary
 *  is restoring the context.  Otherwise, there will need to be
 *  a special assembly routine which does something special in this
 *  case.  Context_Restore should work most of the time.  It will
 *  not work if restarting self conflicts with the stack frame
 *  assumptions of restoring a context.
 */

#define _CPU_Context_Restart_self( _the_context ) \
   _CPU_Context_restore( (_the_context) );

/*
 *  The purpose of this macro is to allow the initial pointer into
 *  A floating point context area (used to save the floating point
 *  context) to be at an arbitrary place in the floating point
 *  context area.
 *
 *  This is necessary because some FP units are designed to have
 *  their context saved as a stack which grows into lower addresses.
 *  Other FP units can be saved by simply moving registers into offsets
 *  from the base of the context area.  Finally some FP units provide
 *  a "dump context" instruction which could fill in from high to low
 *  or low to high based on the whim of the CPU designers.
 */

#define _CPU_Context_Fp_start( _base, _offset ) \
   ( (void *) _Addresses_Add_offset( (_base), (_offset) ) )

/*
 *  This routine initializes the FP context area passed to it to.
 *  There are a few standard ways in which to initialize the
 *  floating point context.  The code included for this macro assumes
 *  that this is a CPU in which a "initial" FP context was saved into
 *  _CPU_Null_fp_context and it simply copies it to the destination
 *  context passed to it.
 *
 *  Other models include (1) not doing anything, and (2) putting
 *  a "null FP status word" in the correct place in the FP context.
 */

#if ( CPU_HARDWARE_FP == TRUE )
#define _CPU_Context_Initialize_fp( _destination ) \
  { \
   *((Context_Control_fp *) *((void **) _destination)) = _CPU_Null_fp_context; \
  }
#endif

/* end of Context handler macros */

/* Fatal Error manager macros */

/*
 *  This routine copies _error into a known place -- typically a stack
 *  location or a register, optionally disables interrupts, and
 *  halts/stops the CPU.
 */

#define _CPU_Fatal_halt( _error ) \
  do { \
    unsigned int _level; \
    _CPU_ISR_Disable(_level); \
    loop: goto loop; \
  } while (0)


extern void mips_break( int error );

/* Bitfield handler macros */

/*
 *  This routine sets _output to the bit number of the first bit
 *  set in _value.  _value is of CPU dependent type Priority_Bit_map_control.
 *  This type may be either 16 or 32 bits wide although only the 16
 *  least significant bits will be used.
 *
 *  There are a number of variables in using a "find first bit" type
 *  instruction.
 *
 *    (1) What happens when run on a value of zero?
 *    (2) Bits may be numbered from MSB to LSB or vice-versa.
 *    (3) The numbering may be zero or one based.
 *    (4) The "find first bit" instruction may search from MSB or LSB.
 *
 *  RTEMS guarantees that (1) will never happen so it is not a concern.
 *  (2),(3), (4) are handled by the macros _CPU_Priority_mask() and
 *  _CPU_Priority_bits_index().  These three form a set of routines
 *  which must logically operate together.  Bits in the _value are
 *  set and cleared based on masks built by _CPU_Priority_mask().
 *  The basic major and minor values calculated by _Priority_Major()
 *  and _Priority_Minor() are "massaged" by _CPU_Priority_bits_index()
 *  to properly range between the values returned by the "find first bit"
 *  instruction.  This makes it possible for _Priority_Get_highest() to
 *  calculate the major and directly index into the minor table.
 *  This mapping is necessary to ensure that 0 (a high priority major/minor)
 *  is the first bit found.
 *
 *  This entire "find first bit" and mapping process depends heavily
 *  on the manner in which a priority is broken into a major and minor
 *  components with the major being the 4 MSB of a priority and minor
 *  the 4 LSB.  Thus (0 << 4) + 0 corresponds to priority 0 -- the highest
 *  priority.  And (15 << 4) + 14 corresponds to priority 254 -- the next
 *  to the lowest priority.
 *
 *  If your CPU does not have a "find first bit" instruction, then
 *  there are ways to make do without it.  Here are a handful of ways
 *  to implement this in software:
 *
 *    - a series of 16 bit test instructions
 *    - a "binary search using if's"
 *    - _number = 0
 *      if _value > 0x00ff
 *        _value >>=8
 *        _number = 8;
 *
 *      if _value > 0x0000f
 *        _value >=8
 *        _number += 4
 *
 *      _number += bit_set_table[ _value ]
 *
 *    where bit_set_table[ 16 ] has values which indicate the first
 *      bit set
 */

#define CPU_USE_GENERIC_BITFIELD_CODE TRUE
#define CPU_USE_GENERIC_BITFIELD_DATA TRUE

#if (CPU_USE_GENERIC_BITFIELD_CODE == FALSE)

#define _CPU_Bitfield_Find_first_bit( _value, _output ) \
  { \
    (_output) = 0;   /* do something to prevent warnings */ \
  }

#endif

/* end of Bitfield handler macros */

/*
 *  This routine builds the mask which corresponds to the bit fields
 *  as searched by _CPU_Bitfield_Find_first_bit().  See the discussion
 *  for that routine.
 */

#if (CPU_USE_GENERIC_BITFIELD_CODE == FALSE)

#define _CPU_Priority_Mask( _bit_number ) \
  ( 1 << (_bit_number) )

#endif

/*
 *  This routine translates the bit numbers returned by
 *  _CPU_Bitfield_Find_first_bit() into something suitable for use as
 *  a major or minor component of a priority.  See the discussion
 *  for that routine.
 */

#if (CPU_USE_GENERIC_BITFIELD_CODE == FALSE)

#define _CPU_Priority_bits_index( _priority ) \
  (_priority)

#endif

/* end of Priority handler macros */

/* functions */

/*
 *  _CPU_Initialize
 *
 *  This routine performs CPU dependent initialization.
 */

void _CPU_Initialize(
  rtems_cpu_table  *cpu_table,
  void      (*thread_dispatch)
);

/*
 *  _CPU_ISR_install_raw_handler
 *
 *  This routine installs a "raw" interrupt handler directly into the
 *  processor's vector table.
 */

void _CPU_ISR_install_raw_handler(
  unsigned32  vector,
  proc_ptr    new_handler,
  proc_ptr   *old_handler
);

/*
 *  _CPU_ISR_install_vector
 *
 *  This routine installs an interrupt vector.
 */

void _CPU_ISR_install_vector(
  unsigned32  vector,
  proc_ptr    new_handler,
  proc_ptr   *old_handler
);

/*
 *  _CPU_Install_interrupt_stack
 *
 *  This routine installs the hardware interrupt stack pointer.
 *
 *  NOTE:  It need only be provided if CPU_HAS_HARDWARE_INTERRUPT_STACK
 *         is TRUE.
 */

void _CPU_Install_interrupt_stack( void );

/*
 *  _CPU_Internal_threads_Idle_thread_body
 *
 *  This routine is the CPU dependent IDLE thread body.
 *
 *  NOTE:  It need only be provided if CPU_PROVIDES_IDLE_THREAD_BODY
 *         is TRUE.
 */

void _CPU_Thread_Idle_body( void );

/*
 *  _CPU_Context_switch
 *
 *  This routine switches from the run context to the heir context.
 */

void _CPU_Context_switch(
  Context_Control  *run,
  Context_Control  *heir
);

/*
 *  _CPU_Context_restore
 *
 *  This routine is generally used only to restart self in an
 *  efficient manner.  It may simply be a label in _CPU_Context_switch.
 *
 *  NOTE: May be unnecessary to reload some registers.
 */

void _CPU_Context_restore(
  Context_Control *new_context
);

/*
 *  _CPU_Context_save_fp
 *
 *  This routine saves the floating point context passed to it.
 */

void _CPU_Context_save_fp(
  void **fp_context_ptr
);

/*
 *  _CPU_Context_restore_fp
 *
 *  This routine restores the floating point context passed to it.
 */

void _CPU_Context_restore_fp(
  void **fp_context_ptr
);

/*  The following routine swaps the endian format of an unsigned int.
 *  It must be static because it is referenced indirectly.
 *
 *  This version will work on any processor, but if there is a better
 *  way for your CPU PLEASE use it.  The most common way to do this is to:
 *
 *     swap least significant two bytes with 16-bit rotate
 *     swap upper and lower 16-bits
 *     swap most significant two bytes with 16-bit rotate
 *
 *  Some CPUs have special instructions which swap a 32-bit quantity in
 *  a single instruction (e.g. i486).  It is probably best to avoid
 *  an "endian swapping control bit" in the CPU.  One good reason is
 *  that interrupts would probably have to be disabled to insure that
 *  an interrupt does not try to access the same "chunk" with the wrong
 *  endian.  Another good reason is that on some CPUs, the endian bit
 *  endianness for ALL fetches -- both code and data -- so the code
 *  will be fetched incorrectly.
 */

static inline unsigned int CPU_swap_u32(
  unsigned int value
)
{
  unsigned32 byte1, byte2, byte3, byte4, swapped;

  byte4 = (value >> 24) & 0xff;
  byte3 = (value >> 16) & 0xff;
  byte2 = (value >> 8)  & 0xff;
  byte1 =  value        & 0xff;

  swapped = (byte1 << 24) | (byte2 << 16) | (byte3 << 8) | byte4;
  return( swapped );
}

#define CPU_swap_u16( value ) \
  (((value&0xff) << 8) | ((value >> 8)&0xff))


#endif



#ifdef __cplusplus
}
#endif

#endif