source: rtems/cpukit/score/cpu/m32c/include/rtems/score/cpu.h @ 924cecd9

/**
 * @file
 * 
 * @brief M32C CPU Dependent Source
 */

/*
 *  This include file contains information pertaining to the XXX
 *  processor.
 *
 *  @note This file is part of a porting template that is intended
 *  to be used as the starting point when porting RTEMS to a new
 *  CPU family.  The following needs to be done when using this as
 *  the starting point for a new port:
 *
 *  + Anywhere there is an XXX, it should be replaced
 *    with information about the CPU family being ported to.
 *
 *  + At the end of each comment section, there is a heading which
 *    says "Port Specific Information:".  When porting to RTEMS,
 *    add CPU family specific information in this section
 */

/*
 *  COPYRIGHT (c) 1989-2008.
 *  On-Line Applications Research Corporation (OAR).
 *
 *  The license and distribution terms for this file may be
 *  found in the file LICENSE in this distribution or at
 *  http://www.rtems.org/license/LICENSE.
 */

#ifndef _RTEMS_SCORE_CPU_H
#define _RTEMS_SCORE_CPU_H

#ifdef __cplusplus
extern "C" {
#endif

#include <rtems/score/basedefs.h>
#include <rtems/score/m32c.h>

/* conditional compilation parameters */

#define RTEMS_USE_16_BIT_OBJECT

/**
 * Does RTEMS manage a dedicated interrupt stack in software?
 *
 * If TRUE, then a stack is allocated in @ref _ISR_Handler_initialization.
 * If FALSE, nothing is done.
 *
 * If the CPU supports a dedicated interrupt stack in hardware,
 * then it is generally the responsibility of the BSP to allocate it
 * and set it up.
 *
 * If the CPU does not support a dedicated interrupt stack, then
 * the porter has two options: (1) execute interrupts on the
 * stack of the interrupted task, and (2) have RTEMS manage a dedicated
 * interrupt stack.
 *
 * If this is TRUE, @ref CPU_ALLOCATE_INTERRUPT_STACK should also be TRUE.
 *
 * Only one of @ref CPU_HAS_SOFTWARE_INTERRUPT_STACK and
 * @ref CPU_HAS_HARDWARE_INTERRUPT_STACK should be set to TRUE.  It is
 * possible that both are FALSE for a particular CPU.  Although it
 * is unclear what that would imply about the interrupt processing
 * procedure on that CPU.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define CPU_HAS_SOFTWARE_INTERRUPT_STACK FALSE

/**
 * Does the CPU follow the simple vectored interrupt model?
 *
 * If TRUE, then RTEMS allocates the vector table it internally manages.
 * If FALSE, then the BSP is assumed to allocate and manage the vector
 * table
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define CPU_SIMPLE_VECTORED_INTERRUPTS TRUE

/**
 * Does this CPU have hardware support for a dedicated interrupt stack?
 *
 * If TRUE, then it must be installed during initialization.
 * If FALSE, then no installation is performed.
 *
 * If this is TRUE, @ref CPU_ALLOCATE_INTERRUPT_STACK should also be TRUE.
 *
 * Only one of @ref CPU_HAS_SOFTWARE_INTERRUPT_STACK and
 * @ref CPU_HAS_HARDWARE_INTERRUPT_STACK should be set to TRUE.  It is
 * possible that both are FALSE for a particular CPU.  Although it
 * is unclear what that would imply about the interrupt processing
 * procedure on that CPU.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define CPU_HAS_HARDWARE_INTERRUPT_STACK TRUE

/**
 * Does RTEMS allocate a dedicated interrupt stack in the Interrupt Manager?
 *
 * If TRUE, then the memory is allocated during initialization.
 * If FALSE, then the memory is allocated during initialization.
 *
 * This should be TRUE is CPU_HAS_SOFTWARE_INTERRUPT_STACK is TRUE.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define CPU_ALLOCATE_INTERRUPT_STACK TRUE

/**
 * Does the RTEMS invoke the user's ISR with the vector number and
 * a pointer to the saved interrupt frame (1) or just the vector
 * number (0)?
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define CPU_ISR_PASSES_FRAME_POINTER FALSE

/**
 * @def CPU_HARDWARE_FP
 *
 * Does the CPU have hardware floating point?
 *
 * If TRUE, then the RTEMS_FLOATING_POINT task attribute is supported.
 * If FALSE, then the RTEMS_FLOATING_POINT task attribute is ignored.
 *
 * If there is a FP coprocessor such as the i387 or mc68881, then
 * the answer is TRUE.
 *
 * The macro name "M32C_HAS_FPU" should be made CPU specific.
 * It indicates whether or not this CPU model has FP support.  For
 * example, it would be possible to have an i386_nofp CPU model
 * which set this to false to indicate that you have an i386 without
 * an i387 and wish to leave floating point support out of RTEMS.
 */

/**
 * @def CPU_SOFTWARE_FP
 *
 * Does the CPU have no hardware floating point and GCC provides a
 * software floating point implementation which must be context
 * switched?
 *
 * This feature conditional is used to indicate whether or not there
 * is software implemented floating point that must be context
 * switched.  The determination of whether or not this applies
 * is very tool specific and the state saved/restored is also
 * compiler specific.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#if ( M32C_HAS_FPU == 1 )
#define CPU_HARDWARE_FP     TRUE
#else
#define CPU_HARDWARE_FP     FALSE
#endif
#define CPU_SOFTWARE_FP     FALSE

#define CPU_CONTEXT_FP_SIZE 0

/**
 * Are all tasks RTEMS_FLOATING_POINT tasks implicitly?
 *
 * If TRUE, then the RTEMS_FLOATING_POINT task attribute is assumed.
 * If FALSE, then the RTEMS_FLOATING_POINT task attribute is followed.
 *
 * So far, the only CPUs in which this option has been used are the
 * HP PA-RISC and PowerPC.  On the PA-RISC, The HP C compiler and
 * gcc both implicitly used the floating point registers to perform
 * integer multiplies.  Similarly, the PowerPC port of gcc has been
 * seen to allocate floating point local variables and touch the FPU
 * even when the flow through a subroutine (like vfprintf()) might
 * not use floating point formats.
 *
 * If a function which you would not think utilize the FP unit DOES,
 * then one can not easily predict which tasks will use the FP hardware.
 * In this case, this option should be TRUE.
 *
 * If @ref CPU_HARDWARE_FP is FALSE, then this should be FALSE as well.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define CPU_ALL_TASKS_ARE_FP     TRUE

/**
 * Should the IDLE task have a floating point context?
 *
 * If TRUE, then the IDLE task is created as a RTEMS_FLOATING_POINT task
 * and it has a floating point context which is switched in and out.
 * If FALSE, then the IDLE task does not have a floating point context.
 *
 * Setting this to TRUE negatively impacts the time required to preempt
 * the IDLE task from an interrupt because the floating point context
 * must be saved as part of the preemption.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define CPU_IDLE_TASK_IS_FP      FALSE

/**
 * Should the saving of the floating point registers be deferred
 * until a context switch is made to another different floating point
 * task?
 *
 * If TRUE, then the floating point context will not be stored until
 * necessary.  It will remain in the floating point registers and not
 * disturned until another floating point task is switched to.
 *
 * If FALSE, then the floating point context is saved when a floating
 * point task is switched out and restored when the next floating point
 * task is restored.  The state of the floating point registers between
 * those two operations is not specified.
 *
 * If the floating point context does NOT have to be saved as part of
 * interrupt dispatching, then it should be safe to set this to TRUE.
 *
 * Setting this flag to TRUE results in using a different algorithm
 * for deciding when to save and restore the floating point context.
 * The deferred FP switch algorithm minimizes the number of times
 * the FP context is saved and restored.  The FP context is not saved
 * until a context switch is made to another, different FP task.
 * Thus in a system with only one FP task, the FP context will never
 * be saved or restored.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define CPU_USE_DEFERRED_FP_SWITCH       TRUE

#define CPU_ENABLE_ROBUST_THREAD_DISPATCH FALSE

/**
 * Does this port provide a CPU dependent IDLE task implementation?
 *
 * If TRUE, then the routine @ref _CPU_Thread_Idle_body
 * must be provided and is the default IDLE thread body instead of
 * @ref _CPU_Thread_Idle_body.
 *
 * If FALSE, then use the generic IDLE thread body if the BSP does
 * not provide one.
 *
 * This is intended to allow for supporting processors which have
 * a low power or idle mode.  When the IDLE thread is executed, then
 * the CPU can be powered down.
 *
 * The order of precedence for selecting the IDLE thread body is:
 *
 *   -#  BSP provided
 *   -#  CPU dependent (if provided)
 *   -#  generic (if no BSP and no CPU dependent)
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define CPU_PROVIDES_IDLE_THREAD_BODY    TRUE

/**
 * Does the stack grow up (toward higher addresses) or down
 * (toward lower addresses)?
 *
 * If TRUE, then the grows upward.
 * If FALSE, then the grows toward smaller addresses.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define CPU_STACK_GROWS_UP               TRUE

/* FIXME: Is this the right value? */
#define CPU_CACHE_LINE_BYTES 2

#define CPU_STRUCTURE_ALIGNMENT RTEMS_ALIGNED( CPU_CACHE_LINE_BYTES )

/**
 * @ingroup CPUInterrupt
 * 
 * The following defines the number of bits actually used in the
 * interrupt field of the task mode.  How those bits map to the
 * CPU interrupt levels is defined by the routine @ref _CPU_ISR_Set_level.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define CPU_MODES_INTERRUPT_MASK   0x00000001

#define CPU_MAXIMUM_PROCESSORS 32

/*
 *  Processor defined structures required for cpukit/score.
 *
 *  Port Specific Information:
 *
 *  XXX document implementation including references if appropriate
 */

/* may need to put some structures here.  */

/**
 * @defgroup CPUContext Processor Dependent Context Management
 *
 * From the highest level viewpoint, there are 2 types of context to save.
 *
 *    -# Interrupt registers to save
 *    -# Task level registers to save
 *
 * Since RTEMS handles integer and floating point contexts separately, this
 * means we have the following 3 context items:
 *
 *    -# task level context stuff::  Context_Control
 *    -# floating point task stuff:: Context_Control_fp
 *    -# special interrupt level context :: CPU_Interrupt_frame
 *
 * On some processors, it is cost-effective to save only the callee
 * preserved registers during a task context switch.  This means
 * that the ISR code needs to save those registers which do not
 * persist across function calls.  It is not mandatory to make this
 * distinctions between the caller/callee saves registers for the
 * purpose of minimizing context saved during task switch and on interrupts.
 * If the cost of saving extra registers is minimal, simplicity is the
 * choice.  Save the same context on interrupt entry as for tasks in
 * this case.
 *
 * Additionally, if gdb is to be made aware of RTEMS tasks for this CPU, then
 * care should be used in designing the context area.
 *
 * On some CPUs with hardware floating point support, the Context_Control_fp
 * structure will not be used or it simply consist of an array of a
 * fixed number of bytes.   This is done when the floating point context
 * is dumped by a "FP save context" type instruction and the format
 * is not really defined by the CPU.  In this case, there is no need
 * to figure out the exact format -- only the size.  Of course, although
 * this is enough information for RTEMS, it is probably not enough for
 * a debugger such as gdb.  But that is another problem.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
/**@{**/

/**
 * @ingroup Management
 * 
 * This defines the minimal set of integer and processor state registers
 * that must be saved during a voluntary context switch from one thread
 * to another.
 */
typedef struct {
  /** This will contain the stack pointer. */
  uint32_t sp;
  /** This will contain the frame base pointer. */
  uint32_t fb;
} Context_Control;

/**
 * @ingroup Management
 *
 * This macro returns the stack pointer associated with @a _context.
 *
 * @param[in] _context is the thread context area to access
 *
 * @return This method returns the stack pointer.
 */
#define _CPU_Context_Get_SP( _context ) \
  (_context)->sp

/**
 * @ingroup Management
 * 
 * This defines the set of integer and processor state registers that must
 * be saved during an interrupt.  This set does not include any which are
 * in @ref Context_Control.
 */
typedef struct {
    /** 
     * This field is a hint that a port will have a number of integer
     * registers that need to be saved when an interrupt occurs or
     * when a context switch occurs at the end of an ISR.
     */
    uint32_t   special_interrupt_register;
} CPU_Interrupt_frame;

/** @} */

/**
 * @defgroup CPUInterrupt Processor Dependent Interrupt Management
 *
 * On some CPUs, RTEMS supports a software managed interrupt stack.
 * This stack is allocated by the Interrupt Manager and the switch
 * is performed in @ref _ISR_Handler.  These variables contain pointers
 * to the lowest and highest addresses in the chunk of memory allocated
 * for the interrupt stack.  Since it is unknown whether the stack
 * grows up or down (in general), this give the CPU dependent
 * code the option of picking the version it wants to use.
 *
 * NOTE: These two variables are required if the macro
 *       @ref CPU_HAS_SOFTWARE_INTERRUPT_STACK is defined as TRUE.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 * 
 */
/**@{**/

/*
 *  Nothing prevents the porter from declaring more CPU specific variables.
 *
 *  Port Specific Information:
 *
 *  XXX document implementation including references if appropriate
 */

/* XXX: if needed, put more variables here */

/**
 * Amount of extra stack (above minimum stack size) required by
 * MPCI receive server thread.  Remember that in a multiprocessor
 * system this thread must exist and be able to process all directives.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define CPU_MPCI_RECEIVE_SERVER_EXTRA_STACK 0

/**
 * This defines the number of entries in the @ref _ISR_Vector_table managed
 * by RTEMS.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define CPU_INTERRUPT_NUMBER_OF_VECTORS      32

/** This defines the highest interrupt vector number for this port. */
#define CPU_INTERRUPT_MAXIMUM_VECTOR_NUMBER  (CPU_INTERRUPT_NUMBER_OF_VECTORS - 1)

/**
 * This is defined if the port has a special way to report the ISR nesting
 * level.  Most ports maintain the variable @a _ISR_Nest_level.
 */
#define CPU_PROVIDES_ISR_IS_IN_PROGRESS FALSE

/** @} */

/**
 * @ingroup CPUContext
 * 
 * Should be large enough to run all RTEMS tests.  This ensures
 * that a "reasonable" small application should not have any problems.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define CPU_STACK_MINIMUM_SIZE          (2048L)

#ifdef __m32cm_cpu__
  #define CPU_SIZEOF_POINTER 4
#else
  #define CPU_SIZEOF_POINTER 2
#endif

/**
 * CPU's worst alignment requirement for data types on a byte boundary.  This
 * alignment does not take into account the requirements for the stack.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define CPU_ALIGNMENT              2

/**
 * This number corresponds to the byte alignment requirement for the
 * heap handler.  This alignment requirement may be stricter than that
 * for the data types alignment specified by @ref CPU_ALIGNMENT.  It is
 * common for the heap to follow the same alignment requirement as
 * @ref CPU_ALIGNMENT.  If the @ref CPU_ALIGNMENT is strict enough for
 * the heap, then this should be set to @ref CPU_ALIGNMENT.
 *
 * NOTE:  This does not have to be a power of 2 although it should be
 *        a multiple of 2 greater than or equal to 2.  The requirement
 *        to be a multiple of 2 is because the heap uses the least
 *        significant field of the front and back flags to indicate
 *        that a block is in use or free.  So you do not want any odd
 *        length blocks really putting length data in that bit.
 *
 *        On byte oriented architectures, @ref CPU_HEAP_ALIGNMENT normally will
 *        have to be greater or equal to than @ref CPU_ALIGNMENT to ensure that
 *        elements allocated from the heap meet all restrictions.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define CPU_HEAP_ALIGNMENT         4

/**
 * This number corresponds to the byte alignment requirement for memory
 * buffers allocated by the partition manager.  This alignment requirement
 * may be stricter than that for the data types alignment specified by
 * @ref CPU_ALIGNMENT.  It is common for the partition to follow the same
 * alignment requirement as @ref CPU_ALIGNMENT.  If the @ref CPU_ALIGNMENT is
 * strict enough for the partition, then this should be set to
 * @ref CPU_ALIGNMENT.
 *
 * NOTE:  This does not have to be a power of 2.  It does have to
 *        be greater or equal to than @ref CPU_ALIGNMENT.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define CPU_PARTITION_ALIGNMENT    CPU_ALIGNMENT

/**
 * This number corresponds to the byte alignment requirement for the
 * stack.  This alignment requirement may be stricter than that for the
 * data types alignment specified by @ref CPU_ALIGNMENT.  If the
 * @ref CPU_ALIGNMENT is strict enough for the stack, then this should be
 * set to 0.
 *
 * NOTE: This must be a power of 2 either 0 or greater than @ref CPU_ALIGNMENT.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define CPU_STACK_ALIGNMENT        0

/*
 *  ISR handler macros
 */

/**
 * @ingroup CPUInterrupt
 * 
 * Support routine to initialize the RTEMS vector table after it is allocated.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define _CPU_Initialize_vectors()

/**
 * @ingroup CPUInterrupt
 * 
 * Disable all interrupts for an RTEMS critical section.  The previous
 * level is returned in @a _isr_cookie.
 *
 * @param[out] _isr_cookie will contain the previous level cookie
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define _CPU_ISR_Disable( _isr_cookie ) \
  do { \
    int _flg; \
    m32c_get_flg( _flg ); \
    _isr_cookie = _flg; \
    __asm__ volatile( "fclr I" ); \
  } while(0)

/**
 * @ingroup CPUInterrupt
 * 
 * Enable interrupts to the previous level (returned by _CPU_ISR_Disable).
 * This indicates the end of an RTEMS critical section.  The parameter
 * @a _isr_cookie is not modified.
 *
 * @param[in] _isr_cookie contain the previous level cookie
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define _CPU_ISR_Enable(_isr_cookie) \
  do { \
    int _flg = (int) (_isr_cookie); \
    m32c_set_flg( _flg ); \
  } while(0)

/**
 * @ingroup CPUInterrupt
 * 
 * This temporarily restores the interrupt to @a _isr_cookie before immediately
 * disabling them again.  This is used to divide long RTEMS critical
 * sections into two or more parts.  The parameter @a _isr_cookie is not
 * modified.
 *
 * @param[in] _isr_cookie contain the previous level cookie
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define _CPU_ISR_Flash( _isr_cookie ) \
  do { \
    int _flg = (int) (_isr_cookie); \
    m32c_set_flg( _flg ); \
    __asm__ volatile( "fclr I" ); \
  } while(0)

RTEMS_INLINE_ROUTINE bool _CPU_ISR_Is_enabled( uint32_t level )
{
  return ( level & 0x40 ) != 0;
}

/**
 * @ingroup CPUInterrupt
 *
 * This routine and @ref _CPU_ISR_Get_level
 * Map the interrupt level in task mode onto the hardware that the CPU
 * actually provides.  Currently, interrupt levels which do not
 * map onto the CPU in a generic fashion are undefined.  Someday,
 * it would be nice if these were "mapped" by the application
 * via a callout.  For example, m68k has 8 levels 0 - 7, levels
 * 8 - 255 would be available for bsp/application specific meaning.
 *This could be used to manage a programmable interrupt controller
 * via the rtems_task_mode directive.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define _CPU_ISR_Set_level( _new_level ) \
  do { \
    if (_new_level) __asm__ volatile( "fclr I" ); \
    else            __asm__ volatile( "fset I" ); \
  } while(0)

/**
 * @ingroup CPUInterrupt
 * 
 * Return the current interrupt disable level for this task in
 * the format used by the interrupt level portion of the task mode.
 *
 * NOTE: This routine usually must be implemented as a subroutine.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
uint32_t   _CPU_ISR_Get_level( void );

/* end of ISR handler macros */

/* Context handler macros */

/**
 * @ingroup CPUContext
 * 
 * Initialize the context to a state suitable for starting a
 * task after a context restore operation.  Generally, this
 * involves:
 *
 *    - setting a starting address
 *    - preparing the stack
 *    - preparing the stack and frame pointers
 *    - setting the proper interrupt level in the context
 *    - initializing the floating point context
 *
 * This routine generally does not set any unnecessary register
 * in the context.  The state of the "general data" registers is
 * undefined at task start time.
 *
 * @param[in] _the_context is the context structure to be initialized
 * @param[in] _stack_base is the lowest physical address of this task's stack
 * @param[in] _size is the size of this task's stack
 * @param[in] _isr is the interrupt disable level
 * @param[in] _entry_point is the thread's entry point.  This is
 *        always @a _Thread_Handler
 * @param[in] _is_fp is TRUE if the thread is to be a floating
 *       point thread.  This is typically only used on CPUs where the
 *       FPU may be easily disabled by software such as on the SPARC
 *       where the PSR contains an enable FPU bit.
 * @param[in] tls_area is the thread-local storage (TLS) area
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
void _CPU_Context_Initialize(
  Context_Control  *the_context,
  uint32_t         *stack_base,
  size_t            size,
  uint32_t          new_level,
  void             *entry_point,
  bool              is_fp,
  void             *tls_area
);

/**
 * This routine is responsible for somehow restarting the currently
 * executing task.  If you are lucky, then all that is necessary
 * is restoring the context.  Otherwise, there will need to be
 * a special assembly routine which does something special in this
 * case.  For many ports, simply adding a label to the restore path
 * of @ref _CPU_Context_switch will work.  On other ports, it may be
 * possibly to load a few arguments and jump to the restore path. It will
 * not work if restarting self conflicts with the stack frame
 * assumptions of restoring a context.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
void _CPU_Context_Restart_self(
  Context_Control  *the_context
) RTEMS_NO_RETURN;

/**
 * This routine initializes the FP context area passed to it to.
 * There are a few standard ways in which to initialize the
 * floating point context.  The code included for this macro assumes
 * that this is a CPU in which a "initial" FP context was saved into
 * @a _CPU_Null_fp_context and it simply copies it to the destination
 * context passed to it.
 *
 * Other floating point context save/restore models include:
 *   -# not doing anything, and
 *   -# putting a "null FP status word" in the correct place in the FP context.
 *
 * @param[in] _destination is the floating point context area
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define _CPU_Context_Initialize_fp( _destination ) \
  { \
   *(*(_destination)) = _CPU_Null_fp_context; \
  }

/* end of Context handler macros */

/* Fatal Error manager macros */

/**
 * This routine copies _error into a known place -- typically a stack
 * location or a register, optionally disables interrupts, and
 * halts/stops the CPU.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
#define _CPU_Fatal_halt( _source, _error ) \
  { \
  }

/* end of Fatal Error manager macros */

#define CPU_USE_GENERIC_BITFIELD_CODE TRUE

/* functions */

/**
 * This routine performs CPU dependent initialization.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
void _CPU_Initialize(void);

/**
 * @ingroup CPUInterrupt
 *
 * This routine installs a "raw" interrupt handler directly into the
 * processor's vector table.
 *
 * @param[in] vector is the vector number
 * @param[in] new_handler is the raw ISR handler to install
 * @param[in] old_handler is the previously installed ISR Handler
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
void _CPU_ISR_install_raw_handler(
  uint32_t    vector,
  proc_ptr    new_handler,
  proc_ptr   *old_handler
);

/**
 * @ingroup CPUInterrupt
 * 
 * This routine installs an interrupt vector.
 *
 * @param[in] vector is the vector number
 * @param[in] new_handler is the RTEMS ISR handler to install
 * @param[in] old_handler is the previously installed ISR Handler
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
void _CPU_ISR_install_vector(
  uint32_t    vector,
  proc_ptr    new_handler,
  proc_ptr   *old_handler
);

/**
 * @ingroup CPUInterrupt
 *
 * This routine installs the hardware interrupt stack pointer.
 *
 * NOTE:  It need only be provided if @ref CPU_HAS_HARDWARE_INTERRUPT_STACK
 *        is TRUE.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
void _CPU_Install_interrupt_stack( void );

/**
 * This routine is the CPU dependent IDLE thread body.
 *
 * NOTE:  It need only be provided if @ref CPU_PROVIDES_IDLE_THREAD_BODY
 *        is TRUE.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
void *_CPU_Thread_Idle_body( uintptr_t ignored );

/**
 * @ingroup CPUContext
 * 
 * This routine switches from the run context to the heir context.
 *
 * @param[in] run points to the context of the currently executing task
 * @param[in] heir points to the context of the heir task
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
void _CPU_Context_switch(
  Context_Control  *run,
  Context_Control  *heir
);

/**
 * @ingroup CPUContext
 * 
 * This routine is generally used only to restart self in an
 * efficient manner.  It may simply be a label in @ref _CPU_Context_switch.
 *
 * @param[in] new_context points to the context to be restored.
 *
 * NOTE: May be unnecessary to reload some registers.
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
void _CPU_Context_restore(
  Context_Control *new_context
) RTEMS_NO_RETURN;

static inline void _CPU_Context_volatile_clobber( uintptr_t pattern )
{
  /* TODO */
}

static inline void _CPU_Context_validate( uintptr_t pattern )
{
  while (1) {
    /* TODO */
  }
}

/* FIXME */
typedef CPU_Interrupt_frame CPU_Exception_frame;

void _CPU_Exception_frame_print( const CPU_Exception_frame *frame );

/**
 * @ingroup CPUEndian
 * 
 * The following routine swaps the endian format of an unsigned int.
 * It must be static because it is referenced indirectly.
 *
 * This version will work on any processor, but if there is a better
 * way for your CPU PLEASE use it.  The most common way to do this is to:
 *
 *    swap least significant two bytes with 16-bit rotate
 *    swap upper and lower 16-bits
 *    swap most significant two bytes with 16-bit rotate
 *
 * Some CPUs have special instructions which swap a 32-bit quantity in
 * a single instruction (e.g. i486).  It is probably best to avoid
 * an "endian swapping control bit" in the CPU.  One good reason is
 * that interrupts would probably have to be disabled to ensure that
 * an interrupt does not try to access the same "chunk" with the wrong
 * endian.  Another good reason is that on some CPUs, the endian bit
 * endianness for ALL fetches -- both code and data -- so the code
 * will be fetched incorrectly.
 *
 * @param[in] value is the value to be swapped
 * @return the value after being endian swapped
 *
 * Port Specific Information:
 *
 * XXX document implementation including references if appropriate
 */
static inline uint32_t CPU_swap_u32(
  uint32_t value
)
{
  uint32_t byte1, byte2, byte3, byte4, swapped;

  byte4 = (value >> 24) & 0xff;
  byte3 = (value >> 16) & 0xff;
  byte2 = (value >> 8)  & 0xff;
  byte1 =  value        & 0xff;

  swapped = (byte1 << 24) | (byte2 << 16) | (byte3 << 8) | byte4;
  return swapped;
}

/**
 * @ingroup CPUEndian
 * 
 * This routine swaps a 16 bir quantity.
 *
 * @param[in] value is the value to be swapped
 * @return the value after being endian swapped
 */
#define CPU_swap_u16( value ) \
  (((value&0xff) << 8) | ((value >> 8)&0xff))

typedef uint32_t CPU_Counter_ticks;

CPU_Counter_ticks _CPU_Counter_read( void );

static inline CPU_Counter_ticks _CPU_Counter_difference(
  CPU_Counter_ticks second,
  CPU_Counter_ticks first
)
{
  return second - first;
}

/** Type that can store a 32-bit integer or a pointer. */
typedef unsigned long CPU_Uint32ptr;

#ifdef __cplusplus
}
#endif

#endif