4.104.114.84.95
Last change
on this file since 82307a11 was
4721cf1,
checked in by Joel Sherrill <joel.sherrill@…>, on 12/03/98 at 23:54:14
|
Patch from Emmanuel Raguet <raguet@…> to add remote debug server
and RPC support to RTEMS. Thanks. :) Email follows:
Hello,
For Xmas, here is the Remote Debugger on RTEMS !
Here are 2 patches for the Remote Debugger on RTEMS for pc386 from Linux
host :
- one for RTEMS it self,
- one for GDB-4.17.
1/ RTEMS patch
--------------
This patch adds 2 libraries :
- a simplified SUN RPC library
- the Remote Debugger library
The configuration command is the following :
../rtems4/configure --target=i386-rtemself --enable-rtemsbsp=pc386
--enable-rdbg
The SUN RPC library is built only if networking is set.
The RDBG library is built if networking and enable-rdbg are set.
The function used to initialize the debugger is :
rtems_rdbg_initialize ();
A special function has been created to force a task to be
in a "debug" state : enterRdbg().
The use of this function is not mandatory.
2/ GDB-4.17 patch
-----------------
This patch create a new RTEMS target for GDB-4.17.
The configuration command is the following :
./configure --enable-shared --target=i386RTEMS
To connect to a target, use :
target rtems [your_site_address]
Then, attach the target using : attach 1
And... Debug ;)
You can obtain the original GDB-4.17 on
ftp://ftp.debian.org/debian/dists/stable/main/source/devel/gdb_4.17.orig.tar.gz
This has been tested from a Debian 2.0.1 linux host.
|
-
Property mode set to
100644
|
File size:
1.4 KB
|
Line | |
---|
1 | /* |
---|
2 | ************************************************************************** |
---|
3 | * |
---|
4 | * Component = rdblib |
---|
5 | * |
---|
6 | * Synopsis = remdeb_f.x |
---|
7 | * |
---|
8 | * |
---|
9 | ************************************************************************** |
---|
10 | */ |
---|
11 | |
---|
12 | struct xdr_regs |
---|
13 | { |
---|
14 | unsigned int tabreg[19]; |
---|
15 | }; |
---|
16 | |
---|
17 | #ifdef RPC_HDR |
---|
18 | |
---|
19 | %/* now define register macros to apply to xdr_reg struct */ |
---|
20 | % |
---|
21 | %#define GS 0 |
---|
22 | %#define FS 1 |
---|
23 | %#define ES 2 |
---|
24 | %#define DS 3 |
---|
25 | %#define EDI 4 |
---|
26 | %#define ESI 5 |
---|
27 | %#define EBP 6 |
---|
28 | %#define ESP 7 |
---|
29 | %#define EBX 8 |
---|
30 | %#define EDX 9 |
---|
31 | %#define ECX 10 |
---|
32 | %#define EAX 11 |
---|
33 | %#define TRAPNO 12 |
---|
34 | %#define ERR 13 |
---|
35 | %#define EIP 14 |
---|
36 | %#define CS 15 |
---|
37 | %#define EFL 16 |
---|
38 | %#define UESP 17 |
---|
39 | %#define SS 18 |
---|
40 | % |
---|
41 | %#define REG_PC tabreg[EIP] /* PC (eip) register offset */ |
---|
42 | %#define REG_SP tabreg[UESP] /* SP (uesp) register offset */ |
---|
43 | %#define REG_FP tabreg[EBP] /* FP (ebp) register offset */ |
---|
44 | |
---|
45 | %/* now define the BREAKPOINT mask technique to a long word */ |
---|
46 | %#define SET_BREAK(l) ((l&0xFFFFFF00) | 0xCC) |
---|
47 | %#define IS_BREAK(l) (((l) & 0xFF) == 0xCC) |
---|
48 | %#define ORG_BREAK(c,p) (((c) & 0xFFFFFF00) | ((p) & 0xFF)) |
---|
49 | %#define IS_STEP(regs) (regs.tabreg[TRAPNO] == 1) /* was step and not break */ |
---|
50 | %#define BREAK_ADJ 1 /* must subtract one from address after bp */ |
---|
51 | %#define BREAK_SIZE 1 /* Breakpoint occupies one byte */ |
---|
52 | |
---|
53 | %#define TARGET_PROC_TYPE 0 |
---|
54 | |
---|
55 | #endif |
---|
56 | |
---|
57 | |
---|
58 | |
---|
Note: See
TracBrowser
for help on using the repository browser.