1 | /* |
---|
2 | * S3C2400 Timer driver |
---|
3 | * |
---|
4 | * This uses timer 1 for timing measurments. |
---|
5 | * |
---|
6 | * The license and distribution terms for this file may be |
---|
7 | * found in the file LICENSE in this distribution or at |
---|
8 | * http://www.rtems.com/license/LICENSE. |
---|
9 | * |
---|
10 | * Notes: |
---|
11 | * This file manages the benchmark timer used by the RTEMS Timing Test |
---|
12 | * Suite. Each measured time period is demarcated by calls to |
---|
13 | * benchmark_timer_initialize() and benchmark_timer_read(). benchmark_timer_read() usually returns |
---|
14 | * the number of microseconds since benchmark_timer_initialize() exitted. |
---|
15 | * |
---|
16 | * It is important that the timer start/stop overhead be determined |
---|
17 | * when porting or modifying this code. |
---|
18 | */ |
---|
19 | |
---|
20 | #include <rtems.h> |
---|
21 | #include <bsp.h> |
---|
22 | #include <s3c24xx.h> |
---|
23 | |
---|
24 | uint32_t g_start; |
---|
25 | uint32_t g_freq; |
---|
26 | |
---|
27 | bool benchmark_timer_find_average_overhead; |
---|
28 | |
---|
29 | |
---|
30 | /* |
---|
31 | * Set up Timer 1 |
---|
32 | */ |
---|
33 | void benchmark_timer_initialize( void ) |
---|
34 | { |
---|
35 | uint32_t cr; |
---|
36 | |
---|
37 | /* stop TIMER1*/ |
---|
38 | cr=rTCON & 0xFFFFF0FF; |
---|
39 | rTCON=(cr | (0x0 << 8)); |
---|
40 | |
---|
41 | /* set MUX for Timer1 to 1/2 */ |
---|
42 | cr=rTCFG1 & 0xFFFFFF0F; |
---|
43 | rTCFG1=(cr | (0<<4)); |
---|
44 | |
---|
45 | /* input freq=PLCK/2 Mhz*/ |
---|
46 | g_freq = get_PCLK() / 2000; |
---|
47 | rTCNTB1 = 0xFFFF; |
---|
48 | |
---|
49 | /* start TIMER1 with manual reload */ |
---|
50 | cr=rTCON & 0xFFFFF0FF; |
---|
51 | rTCON=(cr | (0x1 << 9)); |
---|
52 | rTCON=(cr | (0x1 << 8)); |
---|
53 | |
---|
54 | g_start = rTCNTO1; |
---|
55 | } |
---|
56 | |
---|
57 | /* |
---|
58 | * The following controls the behavior of benchmark_timer_read(). |
---|
59 | * |
---|
60 | * AVG_OVEREHAD is the overhead for starting and stopping the timer. It |
---|
61 | * is usually deducted from the number returned. |
---|
62 | * |
---|
63 | * LEAST_VALID is the lowest number this routine should trust. Numbers |
---|
64 | * below this are "noise" and zero is returned. |
---|
65 | */ |
---|
66 | |
---|
67 | #define AVG_OVERHEAD 0 /* It typically takes X.X microseconds */ |
---|
68 | /* (Y countdowns) to start/stop the timer. */ |
---|
69 | /* This value is in microseconds. */ |
---|
70 | #define LEAST_VALID 1 /* Don't trust a clicks value lower than this */ |
---|
71 | |
---|
72 | int benchmark_timer_read( void ) |
---|
73 | { |
---|
74 | uint32_t t; |
---|
75 | unsigned long long total; |
---|
76 | |
---|
77 | t = rTCNTO1; |
---|
78 | /* |
---|
79 | * Total is calculated by taking into account the number of timer overflow |
---|
80 | * interrupts since the timer was initialized and clicks since the last |
---|
81 | * interrupts. |
---|
82 | */ |
---|
83 | |
---|
84 | total = (g_start - t); |
---|
85 | |
---|
86 | /* convert to microseconds */ |
---|
87 | total = (total*1000) / g_freq; |
---|
88 | |
---|
89 | if ( benchmark_timer_find_average_overhead == 1 ) { |
---|
90 | return (int) total; |
---|
91 | } else if ( total < LEAST_VALID ) { |
---|
92 | return 0; |
---|
93 | } |
---|
94 | |
---|
95 | /* |
---|
96 | * Somehow convert total into microseconds |
---|
97 | */ |
---|
98 | return (total - AVG_OVERHEAD); |
---|
99 | } |
---|
100 | |
---|
101 | void benchmark_timer_disable_subtracting_average_overhead(bool find_flag) |
---|
102 | { |
---|
103 | benchmark_timer_find_average_overhead = find_flag; |
---|
104 | } |
---|
105 | |
---|