source: rtems/c/src/lib/libbsp/powerpc/mpc8260ads/configure.ac @ 14e1c414

4.104.114.84.95
Last change on this file since 14e1c414 was 14e1c414, checked in by Joel Sherrill <joel.sherrill@…>, on Nov 27, 2001 at 12:08:08 PM

2001-11-27 Ralf Corsepius <corsepiu@…>

  • configure.ac: Add RTEMS_BSPOPTS_*(DATA_CACHE_ENABLE), RTEMS_BSPOPTS_*(INSTRUCTION_CACHE_ENABLE).
  • Property mode set to 100644
File size: 2.9 KB
Line 
1## Process this file with autoconf to produce a configure script.
2##
3## $Id$
4
5AC_PREREQ(2.52)
6AC_INIT
7AC_CONFIG_SRCDIR([bsp_specs])
8RTEMS_TOP(../../../../../..)
9AC_CONFIG_AUX_DIR(../../../../../..)
10
11RTEMS_CANONICAL_TARGET_CPU
12AM_INIT_AUTOMAKE(rtems-c-src-lib-libbsp-powerpc-mpc8260,$RTEMS_VERSION,no)
13AM_MAINTAINER_MODE
14
15RTEMS_PROG_CC_FOR_TARGET([-ansi -fasm])
16RTEMS_CANONICALIZE_TOOLS
17
18RTEMS_ENV_RTEMSBSP
19RTEMS_CHECK_CUSTOM_BSP(RTEMS_BSP)
20RTEMS_CHECK_BSP_CACHE(RTEMS_BSP)
21RTEMS_CANONICAL_HOST
22
23RTEMS_BSPOPTS_SET([DATA_CACHE_ENABLE],[*],[0])
24RTEMS_BSPOPTS_HELP([DATA_CACHE_ENABLE],
25[If defined, the data cache will be enabled after address translation
26 is turned on.])
27
28RTEMS_BSPOPTS_SET([INSTRUCTION_CACHE_ENABLE],[*],[0])
29RTEMS_BSPOPTS_HELP([INSTRUCTION_CACHE_ENABLE],
30[If defined, the instruction cache will be enabled after address translation
31 is turned on.])
32
33RTEMS_BSPOPTS_SET([UARTS_USE_TERMIOS],[*],[0])
34RTEMS_BSPOPTS_HELP([UARTS_USE_TERMIOS],
35[Define to 1 if you want termios support for every port.
36 Termios support is independent of the choice of UART I/O mode.])
37
38RTEMS_BSPOPTS_SET([CONSOLE_MINOR],[*],[SCC2_MINOR])
39RTEMS_BSPOPTS_HELP([CONSOLE_MINOR],
40[(BSP--console driver) Must be defined to be one of SMC1_MINOR,
41 SMC2_MINOR, SCC2_MINOR, SCC3_MINOR, or SCC4_MINOR.
42 Determines which device will be registered as /dev/console.])
43
44RTEMS_BSPOPTS_SET([UARTS_IO_MODE],[*],[0])
45RTEMS_BSPOPTS_HELP([UARTS_IO_MODE],
46[(BSP--console driver)
47 Define to 0 or 1 if you want polled I/O performed by RTEMS.
48 Define to 1 if you want interrupt-driven performed by RTEMS.
49 Define to 2 if you want polled I/O performed by EPPCBug.
50 There is no provision to have a mix of interrupt-driven and polled I/O
51 ports, except that the printk port may use a different mode from the
52 other ports. If this is done, do not open the printk port from an RTEMS
53 application. With EPPCBug 1.1, if mode 2 is selected, CONSOLE_MINOR
54 must be set to SMC1_MINOR. This is a deficiency of the firmware: it
55 does not perform serial I/O on any port other than its default debug
56 port, which must be SMC1.])
57
58RTEMS_BSPOPTS_SET([PRINTK_MINOR],[*],[SMC2_MINOR])
59RTEMS_BSPOPTS_HELP([PRINTK_MINOR],
60[(BSP--console driver)
61 Must be defined to be one of SMC1_MINOR, SMC2_MINOR, SCC2_MINOR,
62 SCC3_MINOR, or SCC4_MINOR. Determines which device is used for output
63 by printk(). If the port that printk() uses is also used for other
64 I/O (e.g. if  PRINTK_MINOR == \$CONSOLE_MINOR), then both ports should
65 use the same type of I/O, otherwise the drivers will likely conflict with
66 each other.])
67
68AM_CONFIG_HEADER(include/bspopts.h)
69
70RTEMS_PROJECT_ROOT
71AM_CONDITIONAL(HAS_NETWORKING,test "$HAS_NETWORKING" = "yes")
72
73# Explicitly list a Makefile here
74AC_CONFIG_FILES([Makefile
75clock/Makefile
76console/Makefile
77include/Makefile
78network/Makefile
79irq/Makefile
80vectors/Makefile
81start/Makefile
82startup/Makefile
83wrapup/Makefile])
84
85RTEMS_PPC_EXCEPTIONS([new])
86
87AC_OUTPUT
Note: See TracBrowser for help on using the repository browser.