source: rtems/c/src/lib/libbsp/powerpc/gen5200/configure.ac @ 7a44d06

## Process this file with autoconf to produce a configure script.

AC_PREREQ([2.69])
AC_INIT([rtems-c-src-lib-libbsp-powerpc-gen5200],[_RTEMS_VERSION],[http://www.rtems.org/bugzilla])
AC_CONFIG_SRCDIR([bsp_specs])
RTEMS_TOP(../../../../../..)

RTEMS_CANONICAL_TARGET_CPU
AM_INIT_AUTOMAKE([no-define nostdinc foreign 1.12.2])
RTEMS_BSP_CONFIGURE

RTEMS_PROG_CC_FOR_TARGET
RTEMS_CANONICALIZE_TOOLS
RTEMS_PROG_CCAS

RTEMS_BSPOPTS_SET_DATA_CACHE_ENABLED([*],[1])
RTEMS_BSPOPTS_HELP_DATA_CACHE_ENABLED

RTEMS_BSPOPTS_SET_INSTRUCTION_CACHE_ENABLED([*],[1])
RTEMS_BSPOPTS_HELP_INSTRUCTION_CACHE_ENABLED

RTEMS_BSPOPTS_SET([BENCHMARK_IRQ_PROCESSING],[*],[0])
RTEMS_BSPOPTS_HELP([BENCHMARK_IRQ_PROCESSING],
[If set to !0, enable code to benchmark IRQ processing.])

RTEMS_BSPOPTS_SET([ALLOW_IRQ_NESTING],[icecube],[0])
RTEMS_BSPOPTS_SET([ALLOW_IRQ_NESTING],[*],[1])
RTEMS_BSPOPTS_HELP([ALLOW_IRQ_NESTING],
[If set to !0, allow nested IRQ processing.])

RTEMS_BSPOPTS_SET([BSP_PRESS_KEY_FOR_RESET],[icecube],[1])
RTEMS_BSPOPTS_SET([BSP_PRESS_KEY_FOR_RESET],[*],[0])
RTEMS_BSPOPTS_HELP([BSP_PRESS_KEY_FOR_RESET],
[If set to !0, print a message and wait until pressed before resetting
 board when application exits.])

RTEMS_BSPOPTS_SET([BSP_RESET_BOARD_AT_EXIT],[icecube],[1])
RTEMS_BSPOPTS_SET([BSP_RESET_BOARD_AT_EXIT],[pm520_*],[1])
RTEMS_BSPOPTS_SET([BSP_RESET_BOARD_AT_EXIT],[brs5l],[1])
RTEMS_BSPOPTS_SET([BSP_RESET_BOARD_AT_EXIT],[*],[0])
RTEMS_BSPOPTS_HELP([BSP_RESET_BOARD_AT_EXIT],
[If set to !0, reset the board when the application exits.])

RTEMS_BSPOPTS_SET([BSP_GPIOPCR_INITMASK],[pm520_ze30],[0x037F3F07])
RTEMS_BSPOPTS_SET([BSP_GPIOPCR_INITVAL],[pm520_ze30],[0x01552104])

RTEMS_BSPOPTS_SET([BSP_GPIOPCR_INITMASK],[brs5l],[0xb30F0F77])
RTEMS_BSPOPTS_SET([BSP_GPIOPCR_INITVAL],[brs5l],[0x91050444])

RTEMS_BSPOPTS_SET([BSP_GPIOPCR_INITMASK],[dp2],[0x337F3F77])
RTEMS_BSPOPTS_SET([BSP_GPIOPCR_INITVAL],[dp2],[0x03550040])

RTEMS_BSPOPTS_SET([BSP_GPIOPCR_INITMASK],[*],[0x330F0F77])
RTEMS_BSPOPTS_SET([BSP_GPIOPCR_INITVAL],[*],[0x01050444])

RTEMS_BSPOPTS_HELP([BSP_GPIOPCR_INITMASK],
[Defines the bits cleared in the MPC5200 GPIOPCR register during
initialization.  Must match the hardware requirements.  Must be consistent with
BSP_GPIOPCR_INITVAL.  The bits are cleared via BSP_GPIOPCR_INITMASK and then
set via BSP_GPIOPCR_INITVAL.])
RTEMS_BSPOPTS_HELP([BSP_GPIOPCR_INITVAL],
[Defines the bits set in the MPC5200 GPIOPCR register during initialization.
Must match the hardware requirements.  Must be consistent with
BSP_GPIOPCR_INITMASK.  The bits are cleared via BSP_GPIOPCR_INITMASK and then
set via BSP_GPIOPCR_INITVAL.])

## on ze30, we have PSC1/4/5/6 ...
RTEMS_BSPOPTS_SET([BSP_UART_AVAIL_MASK],[pm520_ze30],[0x39])
## on cr825, we have PSC1/2/3
RTEMS_BSPOPTS_SET([BSP_UART_AVAIL_MASK],[pm520_cr825],[0x07])
## on brs5l, we have PSC1/2/3
RTEMS_BSPOPTS_SET([BSP_UART_AVAIL_MASK],[brs5l],[0x07])
## on icecube, we only have PSC1
RTEMS_BSPOPTS_SET([BSP_UART_AVAIL_MASK],[icecube],[0x01])
## dp2: PSC2 (via USB connector), PSC6 (GPS module)
RTEMS_BSPOPTS_SET([BSP_UART_AVAIL_MASK],[dp2],[0x22])
## default
RTEMS_BSPOPTS_SET([BSP_UART_AVAIL_MASK],[*],[0x01])
RTEMS_BSPOPTS_HELP([BSP_UART_AVAIL_MASK],
[bit mask to specify the UARTS (PSCs), which should be enabled on this board. 
 Must match the hardware requirements. PSC1 corresponds to the LSB])

RTEMS_BSPOPTS_SET([MPC5200_PSC_INDEX_FOR_GPS_MODULE],[dp2],[5])
RTEMS_BSPOPTS_HELP([MPC5200_PSC_INDEX_FOR_GPS_MODULE],[PSC index for GPS module, if defined results in '/dev/gps'])

RTEMS_BSPOPTS_SET([SINGLE_CHAR_MODE],[*],[])
RTEMS_BSPOPTS_HELP([SINGLE_CHAR_MODE],[enable single character mode for the PSC console driver])

RTEMS_BSPOPTS_SET([UARTS_USE_TERMIOS_INT],[*],[1])
RTEMS_BSPOPTS_HELP([UARTS_USE_TERMIOS_INT],[enable interrupt support for the PSC console driver])

RTEMS_BSPOPTS_SET([PRINTK_MINOR],[dp2],[1])
RTEMS_BSPOPTS_SET([PRINTK_MINOR],[*],[0])
RTEMS_BSPOPTS_HELP([PRINTK_MINOR],[console minor number used by printk()])

RTEMS_BSPOPTS_SET([MPC5200_BOARD_PM520_ZE30],[pm520_ze30],[1])
RTEMS_BSPOPTS_HELP([MPC5200_BOARD_PM520_ZE30],
[enable settings for PM520 ZE30])

RTEMS_BSPOPTS_SET([MPC5200_BOARD_PM520_CR825],[pm520_cr825],[1])
RTEMS_BSPOPTS_HELP([MPC5200_BOARD_PM520_CR825],
[enable settings for PM520 CR825])

RTEMS_BSPOPTS_SET([MPC5200_BOARD_ICECUBE],[icecube],[1])
RTEMS_BSPOPTS_HELP([MPC5200_BOARD_ICECUBE],
[enable settings for IceCube])

RTEMS_BSPOPTS_SET([MPC5200_BOARD_BRS5L],[brs5l],[1])
RTEMS_BSPOPTS_HELP([MPC5200_BOARD_BRS5L],
[enable settings for BRS5L])

RTEMS_BSPOPTS_SET([MPC5200_BOARD_DP2],[dp2],[1])
RTEMS_BSPOPTS_HELP([MPC5200_BOARD_DP2],
[enable settings for DP2])

RTEMS_BSPOPTS_SET([HAS_UBOOT],[pm520*],[1])
RTEMS_BSPOPTS_SET([HAS_UBOOT],[icecube],[1])
RTEMS_BSPOPTS_SET([HAS_UBOOT],[dp2],[1])
RTEMS_BSPOPTS_HELP([HAS_UBOOT],[enable U-Boot startup])

RTEMS_CHECK_NETWORKING
AM_CONDITIONAL(HAS_NETWORKING,test "$HAS_NETWORKING" = "yes")

# Explicitly list all Makefiles here
AC_CONFIG_FILES([Makefile])

RTEMS_BSP_CLEANUP_OPTIONS(0, 0)
RTEMS_BSP_LINKCMDS

RTEMS_PPC_EXCEPTIONS

AC_OUTPUT