source: rtems/c/src/lib/libbsp/m68k/mvme136/include/bsp.h @ df49c60

4.104.114.84.95
Last change on this file since df49c60 was df49c60, checked in by Joel Sherrill <joel.sherrill@…>, on Jun 12, 2000 at 3:00:15 PM

Merged from 4.5.0-beta3a

  • Property mode set to 100644
File size: 4.5 KB
Line 
1/*  bsp.h
2 *
3 *  This include file contains all MVME136 board IO definitions.
4 *
5 *  COPYRIGHT (c) 1989-1999.
6 *  On-Line Applications Research Corporation (OAR).
7 *
8 *  The license and distribution terms for this file may be
9 *  found in the file LICENSE in this distribution or at
10 *  http://www.OARcorp.com/rtems/license.html.
11 *
12 *  $Id$
13 */
14
15#ifndef __MVME136_h
16#define __MVME136_h
17
18#ifdef __cplusplus
19extern "C" {
20#endif
21
22#include <rtems.h>
23#include <clockdrv.h>
24#include <console.h>
25#include <iosupp.h>
26
27/*
28 *  confdefs.h overrides for this BSP:
29 *   - number of termios serial ports (defaults to 1)
30 *   - Interrupt stack space is not minimum if defined.
31 */
32
33/* #define CONFIGURE_NUMBER_OF_TERMIOS_PORTS 2 */
34#define CONFIGURE_INTERRUPT_STACK_MEMORY  (4 * 1024)
35
36/*
37 *  Define the time limits for RTEMS Test Suite test durations.
38 *  Long test and short test duration limits are provided.  These
39 *  values are in seconds and need to be converted to ticks for the
40 *  application.
41 *
42 */
43
44#define MAX_LONG_TEST_DURATION       300 /* 5 minutes = 300 seconds */
45#define MAX_SHORT_TEST_DURATION      3   /* 3 seconds */
46
47/*
48 *  Define the interrupt mechanism for Time Test 27
49 *
50 *  NOTE: Use the MPCSR vector for the MVME136
51 */
52
53#define MUST_WAIT_FOR_INTERRUPT 0
54
55#define Install_tm27_vector( handler ) set_vector( (handler), 75, 1 )
56
57#define Cause_tm27_intr()  (*(volatile rtems_unsigned8 *)0xfffb006b) = 0x80
58
59#define Clear_tm27_intr()  (*(volatile rtems_unsigned8 *)0xfffb006b) = 0x00
60
61#define Lower_tm27_intr()
62
63/*
64 *  Simple spin delay in microsecond units for device drivers.
65 *  This is very dependent on the clock speed of the target.
66 */
67
68#define delay( microseconds ) \
69  { register rtems_unsigned32 _delay=(microseconds); \
70    register rtems_unsigned32 _tmp=123; \
71    asm volatile( "0: \
72                     nbcd      %0 ; \
73                     nbcd      %0 ; \
74                     dbf       %1,0b" \
75                  : "=d" (_tmp), "=d" (_delay) \
76                  : "0"  (_tmp), "1"  (_delay) ); \
77  }
78
79/* Constants */
80
81#define RAM_START 0
82#define RAM_END   0x100000
83
84#define M681ADDR      0xfffb0040         /* address of the M68681 chip */
85#define RXRDYB        0x01               /* status reg recv ready mask */
86#define TXRDYB        0x04               /* status reg trans ready mask */
87#define PARITYERR     0x20               /* status reg parity error mask */
88#define FRAMEERR      0x40               /* status reg frame error mask */
89
90
91#define FOREVER       1                  /* infinite loop */
92
93/* Structures */
94
95struct r_m681_info {
96  char fill1[ 5 ];                       /* channel A regs ( not used ) */
97  char isr;                              /* interrupt status reg */
98  char fill2[ 2 ];                       /* counter regs (not used) */
99  char mr1mr2b;                          /* MR1B and MR2B regs */
100  char srb;                              /* status reg channel B */
101  char fill3;                            /* do not access */
102  char rbb;                              /* receive buffer channel B */
103  char ivr;                              /* interrupt vector register */
104};
105
106struct w_m681_info {
107  char fill1[ 4 ];                       /* channel A regs (not used) */
108  char acr;                              /* auxillary control reg */
109  char imr;                              /* interrupt mask reg */
110  char fill2[ 2 ];                       /* counter regs (not used) */
111  char mr1mr2b;                          /* MR1B and MR2B regs */
112  char csrb;                             /* clock select reg */
113  char crb;                              /* command reg */
114  char tbb;                              /* transmit buffer channel B */
115  char ivr;                              /* interrupt vector register */
116};
117
118#ifdef M136_INIT
119#undef EXTERN
120#define EXTERN
121#else
122#undef EXTERN
123#define EXTERN extern
124#endif
125
126/* miscellaneous stuff assumed to exist */
127
128extern rtems_configuration_table BSP_Configuration;
129
130/* M68681 DUART chip register variables */
131
132EXTERN volatile struct r_m681_info *_Read_m681;  /* M68681 read registers */
133EXTERN volatile struct w_m681_info *_Write_m681; /* M68681 write registers */
134
135extern m68k_isr_entry M68Kvec[];   /* vector table address */
136
137/*
138 *  Device Driver Table Entries
139 */
140
141/*
142 * NOTE: Use the standard Console driver entry
143 */
144 
145/*
146 * NOTE: Use the standard Clock driver entry
147 */
148
149/* functions */
150
151void bsp_cleanup( void );
152
153m68k_isr_entry set_vector(
154  rtems_isr_entry     handler,
155  rtems_vector_number vector,
156  int                 type
157);
158
159#ifdef __cplusplus
160}
161#endif
162
163#endif
164/* end of include file */
Note: See TracBrowser for help on using the repository browser.