1 | /* |
---|
2 | * Initialize 68360 hardware |
---|
3 | * |
---|
4 | * W. Eric Norum |
---|
5 | * Saskatchewan Accelerator Laboratory |
---|
6 | * University of Saskatchewan |
---|
7 | * Saskatoon, Saskatchewan, CANADA |
---|
8 | * eric@skatter.usask.ca |
---|
9 | * |
---|
10 | * $Id$ |
---|
11 | */ |
---|
12 | |
---|
13 | #include <rtems.h> |
---|
14 | #include <bsp.h> |
---|
15 | #include "mc68360.h" |
---|
16 | |
---|
17 | void |
---|
18 | _Init68360 (void) |
---|
19 | { |
---|
20 | int i; |
---|
21 | extern void *_RomBase, *_RamBase; |
---|
22 | m68k_isr_entry *vbr; |
---|
23 | extern void _ClearBSSAndStart (void); |
---|
24 | |
---|
25 | /* |
---|
26 | * Step 6: Is this a power-up reset? |
---|
27 | * For now we just ignore this and do *all* the steps |
---|
28 | * Someday we might want to: |
---|
29 | * if (Hard, Loss of Clock, Power-up) |
---|
30 | * Do all steps |
---|
31 | * else if (Double bus fault, watchdog or soft reset) |
---|
32 | * Skip to step 12 |
---|
33 | * else (must be a CPU32+ reset command) |
---|
34 | * Skip to step 14 |
---|
35 | */ |
---|
36 | |
---|
37 | /* |
---|
38 | * Step 7: Deal with clock synthesizer |
---|
39 | * HARDWARE: |
---|
40 | * Change if you're not using an external 25 MHz oscillator. |
---|
41 | */ |
---|
42 | m360.clkocr = 0x8F; /* No more writes, no clock outputs */ |
---|
43 | m360.pllcr = 0xD000; /* PLL, no writes, no prescale, */ |
---|
44 | /* no LPSTOP slowdown, PLL X1 */ |
---|
45 | m360.cdvcr = 0x8000; /* No more writes, no clock division */ |
---|
46 | |
---|
47 | /* |
---|
48 | * Step 8: Initialize system protection |
---|
49 | * Disable watchdog FIXME: Should use watchdog!!!! |
---|
50 | * Watchdog causes system reset |
---|
51 | * Fastest watchdog timeout |
---|
52 | * Enable double bus fault monitor |
---|
53 | * Enable bus monitor external |
---|
54 | * 128 clocks for external timeout |
---|
55 | */ |
---|
56 | m360.sypcr = 0x4F; |
---|
57 | |
---|
58 | /* |
---|
59 | * Step 9: Clear parameter RAM and reset communication processor module |
---|
60 | */ |
---|
61 | for (i = 0 ; i < 192 ; i += sizeof (long)) { |
---|
62 | *((long *)((char *)&m360 + 0xC00 + i)) = 0; |
---|
63 | *((long *)((char *)&m360 + 0xD00 + i)) = 0; |
---|
64 | *((long *)((char *)&m360 + 0xE00 + i)) = 0; |
---|
65 | *((long *)((char *)&m360 + 0xF00 + i)) = 0; |
---|
66 | } |
---|
67 | m360.cr = M360_CR_RST | M360_CR_FLG; |
---|
68 | |
---|
69 | /* |
---|
70 | * Step 10: Write PEPAR |
---|
71 | * SINTOUT not used (CPU32+ mode) |
---|
72 | * CF1MODE=00 (CONFIG1 input) |
---|
73 | * RAS1* double drive |
---|
74 | * A31-A28 |
---|
75 | * OE* output |
---|
76 | * CAS2* / CAS3* |
---|
77 | * CAS0* / CAS1* |
---|
78 | * CS7* |
---|
79 | * AVEC* |
---|
80 | * HARDWARE: |
---|
81 | * Change if you are using a different memory configuration |
---|
82 | * (static RAM, external address multiplexing, etc). |
---|
83 | */ |
---|
84 | m360.pepar = 0x0100; |
---|
85 | |
---|
86 | /* |
---|
87 | * Step 11: Remap Chip Select 0 (CS0*), set up GMR |
---|
88 | * 1024 addresses per DRAM page (1M DRAM chips) |
---|
89 | * 60 nsec DRAM |
---|
90 | * 180 nsec ROM (3 wait states) |
---|
91 | * HARDWARE: |
---|
92 | * Change if you are using a different memory configuration |
---|
93 | */ |
---|
94 | m360.gmr = M360_GMR_RCNT(24) | M360_GMR_RFEN | M360_GMR_RCYC(0) | |
---|
95 | M360_GMR_PGS(3) | M360_GMR_DPS_32BIT | M360_GMR_NCS | |
---|
96 | M360_GMR_GAMX; |
---|
97 | m360.memc[0].br = (unsigned long)&_RomBase | M360_MEMC_BR_WP | |
---|
98 | M360_MEMC_BR_V; |
---|
99 | m360.memc[0].or = M360_MEMC_OR_WAITS(3) | M360_MEMC_OR_512KB | |
---|
100 | M360_MEMC_OR_8BIT; |
---|
101 | |
---|
102 | /* |
---|
103 | * Step 12: Initialize the system RAM |
---|
104 | * Set up option/base registers |
---|
105 | * 4 MB DRAM |
---|
106 | * 60 nsec DRAM |
---|
107 | * Wait for chips to power up |
---|
108 | * Perform 8 read cycles |
---|
109 | * Set all parity bits to correct state |
---|
110 | * Enable parity checking |
---|
111 | * HARDWARE: |
---|
112 | * Change if you are using a different memory configuration |
---|
113 | */ |
---|
114 | m360.memc[1].or = M360_MEMC_OR_TCYC(0) | M360_MEMC_OR_4MB | |
---|
115 | M360_MEMC_OR_DRAM; |
---|
116 | m360.memc[1].br = (unsigned long)&_RamBase | M360_MEMC_BR_V; |
---|
117 | for (i = 0; i < 50000; i++) |
---|
118 | continue; |
---|
119 | for (i = 0; i < 8; ++i) |
---|
120 | *((volatile unsigned long *)(unsigned long)&_RamBase); |
---|
121 | for (i = 0 ; i < 4*1024*1024 ; i += sizeof (unsigned long)) { |
---|
122 | volatile unsigned long *lp; |
---|
123 | lp = (unsigned long *)((unsigned char *)&_RamBase + i); |
---|
124 | *lp = *lp; |
---|
125 | } |
---|
126 | m360.memc[1].br = (unsigned long)&_RamBase | M360_MEMC_BR_PAREN | |
---|
127 | M360_MEMC_BR_V; |
---|
128 | |
---|
129 | /* |
---|
130 | * Step 13: Copy the exception vector table to system RAM |
---|
131 | */ |
---|
132 | asm volatile ("movec vbr,%0" : "=r" (vbr) : ); |
---|
133 | for (i = 0; i < 256; ++i) |
---|
134 | M68Kvec[i] = vbr[i]; |
---|
135 | asm volatile ("movec %0,vbr" : : "r" (M68Kvec)); |
---|
136 | |
---|
137 | /* |
---|
138 | * Step 14: More system initialization |
---|
139 | * SDCR (Serial DMA configuratin register) |
---|
140 | * Give SDMA priority over all interrupt handlers |
---|
141 | * Set DMA arbiration level to 4 |
---|
142 | * CICR (CPM interrupt configuration register): |
---|
143 | * SCC1 requests at SCCa position |
---|
144 | * SCC2 requests at SCCb position |
---|
145 | * SCC3 requests at SCCc position |
---|
146 | * SCC4 requests at SCCd position |
---|
147 | * Interrupt request level 4 |
---|
148 | * Maintain original priority order |
---|
149 | * Vector base 128 |
---|
150 | * SCCs priority grouped at top of table |
---|
151 | */ |
---|
152 | m360.sdcr = M360_SDMA_SISM_7 | M360_SDMA_SAID_4; |
---|
153 | m360.cicr = (3 << 22) | (2 << 20) | (1 << 18) | (0 << 16) | |
---|
154 | (4 << 13) | (0x1F << 8) | (128); |
---|
155 | |
---|
156 | /* |
---|
157 | * Step 15: Set module configuration register |
---|
158 | * Disable timers during FREEZE |
---|
159 | * Enable bus monitor during FREEZE |
---|
160 | * BCLRO* arbitration level 3 |
---|
161 | * No show cycles |
---|
162 | * User/supervisor access |
---|
163 | * Bus clear interupt service level 7 |
---|
164 | * SIM60 interrupt sources higher priority than CPM |
---|
165 | */ |
---|
166 | m360.mcr = 0x4C7F; |
---|
167 | |
---|
168 | /* |
---|
169 | * Clear BSS, switch stacks and call main() |
---|
170 | */ |
---|
171 | _ClearBSSAndStart (); |
---|
172 | } |
---|