source: rtems/c/src/lib/libbsp/i386/shared/comm/uart.h @ ca312cb

/*
 * This software is Copyright (C) 1998 by T.sqware - all rights limited
 * It is provided in to the public domain "as is", can be freely modified
 * as far as this copyight notice is kept unchanged, but does not imply
 * an endorsement by T.sqware of the product in which it is included.
 */

#ifndef _BSPUART_H
#define _BSPUART_H

#ifdef __cplusplus
extern "C" {
#endif

void BSP_uart_init(int uart, unsigned long baud, unsigned long databits, unsigned long parity, unsigned long stopbits, int hwFlow);
void BSP_uart_set_attributes(int uart, unsigned long baud, unsigned long databits, unsigned long parity, unsigned long stopbits);
void BSP_uart_set_baud(int uart, unsigned long baud);
void BSP_uart_intr_ctrl(int uart, int cmd);
void BSP_uart_throttle(int uart);
void BSP_uart_unthrottle(int uart);
int  BSP_uart_polled_status(int uart);
void BSP_uart_polled_write(int uart, int val);
int  BSP_uart_polled_read(int uart);
void BSP_uart_termios_set(int uart, void *ttyp);
int  BSP_uart_termios_read_com1(int uart);
int  BSP_uart_termios_read_com2(int uart);
int  BSP_uart_termios_write_com1(int minor, const char *buf, int len);
int  BSP_uart_termios_write_com2(int minor, const char *buf, int len);
void BSP_uart_termios_isr_com1();
void BSP_uart_termios_isr_com2();
void BSP_uart_dbgisr_com1(void);
void BSP_uart_dbgisr_com2(void);
extern unsigned BSP_poll_char_via_serial(void);
extern void BSP_output_char_via_serial(int val);
extern int BSPConsolePort;
extern int BSPBaseBaud;
/*
 * Command values for BSP_uart_intr_ctrl(),
 * values are strange in order to catch errors 
 * with assert
 */
#define BSP_UART_INTR_CTRL_DISABLE  (0)
#define BSP_UART_INTR_CTRL_GDB      (0xaa) /* RX only */
#define BSP_UART_INTR_CTRL_ENABLE   (0xbb) /* Normal operations */
#define BSP_UART_INTR_CTRL_TERMIOS  (0xcc) /* RX & line status */

/* Return values for uart_polled_status() */
#define BSP_UART_STATUS_ERROR    (-1) /* No character */
#define BSP_UART_STATUS_NOCHAR   (0)  /* No character */
#define BSP_UART_STATUS_CHAR     (1)  /* Character present */
#define BSP_UART_STATUS_BREAK    (2)  /* Break point is detected */

/* PC UART definitions */
#define BSP_UART_COM1            (0)
#define BSP_UART_COM2            (1)

/*
 * Base IO for UART
 */

#define COM1_BASE_IO    0x3F8
#define COM2_BASE_IO    0x2F8

/*
 * Offsets from base
 */

/* DLAB 0 */
#define RBR  (0)    /* Rx Buffer Register (read) */
#define THR  (0)    /* Tx Buffer Register (write) */
#define IER  (1)    /* Interrupt Enable Register */

/* DLAB X */
#define IIR  (2)    /* Interrupt Ident Register (read) */
#define FCR  (2)    /* FIFO Control Register (write) */
#define LCR  (3)    /* Line Control Register */
#define MCR  (4)    /* Modem Control Register */
#define LSR  (5)    /* Line Status Register */
#define MSR  (6)    /* Modem Status  Register */
#define SCR  (7)    /* Scratch register */

/* DLAB 1 */
#define DLL  (0)    /* Divisor Latch, LSB */
#define DLM  (1)    /* Divisor Latch, MSB */
#define AFR  (2)    /* Alternate Function register */

/*
 * Interrupt source definition via IIR
 */
#define MODEM_STATUS                            0
#define NO_MORE_INTR                            1
#define TRANSMITTER_HODING_REGISTER_EMPTY       2
#define RECEIVER_DATA_AVAIL                     4
#define RECEIVER_ERROR                          6
#define CHARACTER_TIMEOUT_INDICATION            12

/*
 * Bits definition of IER
 */
#define RECEIVE_ENABLE          0x1
#define TRANSMIT_ENABLE         0x2
#define RECEIVER_LINE_ST_ENABLE 0x4
#define MODEM_ENABLE            0x8
#define INTERRUPT_DISABLE       0x0

/*
 * Bits definition of the Line Status Register (LSR)
 */
#define DR      0x01    /* Data Ready */
#define OE      0x02    /* Overrun Error */
#define PE      0x04    /* Parity Error */
#define FE      0x08    /* Framing Error */
#define BI      0x10    /* Break Interrupt */
#define THRE    0x20    /* Transmitter Holding Register Empty */
#define TEMT    0x40    /* Transmitter Empty */
#define ERFIFO  0x80    /* Error receive Fifo */

/*
 * Bits definition of the MODEM Control Register (MCR)
 */
#define DTR     0x01    /* Data Terminal Ready */
#define RTS     0x02    /* Request To Send */
#define OUT_1   0x04    /* Output 1, (reserved on COMPAQ I/O Board) */
#define OUT_2   0x08    /* Output 2, Enable Asynchronous Port Interrupts */
#define LB      0x10    /* Enable Internal Loop Back */

/*
 * Bits definition of the Line Control Register (LCR)
 */
#define CHR_5_BITS 0
#define CHR_6_BITS 1
#define CHR_7_BITS 2
#define CHR_8_BITS 3

#define WL      0x03    /* Word length mask */
#define STB     0x04    /* 1 Stop Bit, otherwise 2 Stop Bits */
#define PEN     0x08    /* Parity Enabled */
#define EPS     0x10    /* Even Parity Select, otherwise Odd */
#define SP      0x20    /* Stick Parity */
#define BCB     0x40    /* Break Control Bit */
#define DLAB    0x80    /* Enable Divisor Latch Access */

/*
 * Bits definition of the MODEM Status Register (MSR)
 */
#define DCTS    0x01    /* Delta Clear To Send */
#define DDSR    0x02    /* Delta Data Set Ready */
#define TERI    0x04    /* Trailing Edge Ring Indicator */
#define DDCD    0x08    /* Delta Carrier Detect Indicator */
#define CTS     0x10    /* Clear To Send (when loop back is active) */
#define DSR     0x20    /* Data Set Ready (when loop back is active) */
#define RI      0x40    /* Ring Indicator (when loop back is active) */
#define DCD     0x80    /* Data Carrier Detect (when loop back is active) */

/*
 * Bits definition of the FIFO Control Register : WD16C552 or NS16550
 */

#define FIFO_CTRL   0x01    /* Set to 1 permit access to other bits */
#define FIFO_EN     0x01    /* Enable the FIFO */
#define XMIT_RESET  0x02    /* Transmit FIFO Reset */
#define RCV_RESET   0x04    /* Receive FIFO Reset */
#define FCR3        0x08    /* do not understand manual! */

#define RECEIVE_FIFO_TRIGGER1   0x0  /* trigger recieve interrupt after 1 byte  */
#define RECEIVE_FIFO_TRIGGER4   0x40 /* trigger recieve interrupt after 4 byte  */
#define RECEIVE_FIFO_TRIGGER8   0x80 /* trigger recieve interrupt after 8 byte  */
#define RECEIVE_FIFO_TRIGGER12  0xc0 /* trigger recieve interrupt after 12 byte */
#define TRIG_LEVEL              0xc0 /* Mask for the trigger level              */

#ifdef __cplusplus
}
#endif


#endif /* _BSPUART_H */